Watch Dog Timer Enable; Usb Wake-Up - Supermicro X10SDV User Manual

Watch Dog Timer Enable

Watch Dog (JWD1) is a system monitor that
can be used to enter LAN bypass default set-
tings, reset the system or enter NMI when
the Timer expires. Close pins 1-2 to reset the
system if an application hangs. Close pins 2-3
to generate a non-maskable interrupt signal
for the application that hangs. Open all pins
to enter LAN pair default mode only. See the
table on the right for jumper settings. Watch
Dog may be enabled in the BIOS Setup. The
default timer is around 5 minutes.

USB Wake-Up

Use the JPUSB1 jumper to enable the func-
tion of "System Wake-Up via USB devices" for
USB0/1. This jumper allows you to "wake-up"
the system by pressing a key on the USB key-
board or by clicking the USB mouse of your
system. The JPUSB1 jumper is used together
with the USB Wake-Up function in the BIOS.
Enable both the jumper and the BIOS setting
to enable this function. See the table on the
right for jumper settings.
JI2C1/JI2C2: JBR1
1-2:ENABLE 1-2:NORMAL
BAR CODE
2-3:DISABLE 2-3:BIOS RECOVERY
JPG1:
1-2:ENABLE
2-3:DISABLE
JPS1:SAS
1-2:ENABLE
2-3:DISABLE
JWD1:WATCH DOG
1-2:RST
2-3:NMI JL1: CHASSIS
INTRUSION
JOH1-OH
MP_SRW2
JIPMB1
BMC
AST2400
MP_SRW1
JMP1
PCI-E 2.0 X1 / I-SATA5
COM1
A
JLANLED1
JTGLED1
JOH1
LSI
A
2116
LEDS1
(-7TP4F/-7TP8F)
I-SATA3
JSAS4
JSAS3
L-SAS8-11 L-SAS12-15
I-SATA2
PRESS FIT
LED7
A
C
UID
VGA
JPL3:
LAN3/4/5/6
M2_SRW3
1-2:ENABLE
2-3:DISABLE
C
LED8
PHY
10GbE
CS2447
A
C
LEDM1
M2_SRW2
i350
AM4
(-7TP8F/
-TP8F)
JPTG1
M2_SRW1
JPME2
JMD1: M.2
PCI-E 3.0 X4 / I-SATA4
JD1
JTPM1
PRESS FIT
USB 2
JSAS1
L-SAS0-3
PRESS FIT
PRESS FIT
LED3
FAN4
JF1
2-29
Pin#
1-2
2-3
Open
Pin#
1-2
2-3
A. Watch Dog Enable
B. USB Wake-Up
PRESS FIT
LAN 5/6 LAN 3/4
A
A
C C
A A
C C
JPL1/JPL2:
LAN 7/8 LAN1/ LAN2
1-2:ENABLE 2-3:DISABLE
Intel Xeon
D-1500
SoC
JBT1:
CMOS
CLEAR
BT1
FAN3
JGP1
JF1:
PWR OH NIC2 HDD PWR
RST X FF NIC1 LED
ON LED
Chapter 2: Installation
Watch Dog
Jumper Settings
Definition
Reset (Default)
NMI
LAN pairs set to default
mode without reset
or NMI
USB Wake-up
Jumper Settings
Definition
Enabled (Default)
Disabled
IPMI_LAN
LAN 1/2
USB 0/1(3.0)
B
JPUSB1
JPV1
JPI2C1
JPW1
JPH1