Cmos Clear; Pci-E Slot Smb Enable; C1/I 2 C2) - Supermicro X10SDV User Manual

X10SDV Flex ATX Series Motherboard User's Manual

CMOS Clear

JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads
to prevent accidental clearing of CMOS. To clear CMOS, use a metal object such
as a small screwdriver to touch both pads at the same time to short the connec-
tion. Always remove the AC power cord from the system before clearing CMOS.
Note 1: For an ATX power supply, you must completely shut down the
system, remove the AC power cord, and then short JBT1 to clear CMOS.
Note 2: Be sure to remove the onboard CMOS Battery before you short
JBT1 to clear CMOS.
Note 3: Clearing CMOS will also clear all passwords.
PCI-E Slot SMB Enable (I
Use jumpers I C1/I
2
SMB (System Management Bus) support
to improve system management for the
onboard PCI-E slot. See the table on the
right for jumper settings.
JI2C1/JI2C2: JBR1
1-2:ENABLE 1-2:NORMAL BAR CODE
2-3:DISABLE 2-3:BIOS RECOVERY
JPG1:
1-2:ENABLE
2-3:DISABLE
JPS1:SAS
1-2:ENABLE
2-3:DISABLE
JWD1:WATCH DOG
1-2:RST
2-3:NMI JL1: CHASSIS
INTRUSION
JOH1-OH
MP_SRW2
JIPMB1
MP_SRW1
B
C
JMP1
PCI-E 2.0 X1 / I-SATA5
COM1
JLANLED1
JTGLED1
JOH1
LSI
A
2116
LEDS1
(-7TP4F/-7TP8F)
I-SATA3
JSAS3
L-SAS8-11
I-SATA2 PRESS FIT
C1/I C2)
2 2
C2 to enable PCI
2
LED7
A
C
UID
VGA
M2_SRW3
C
LED8
PHY
10GbE
CS2447
BMC
A
C
LEDM1
AST2400
M2_SRW2
i350
AM4
(-7TP8F/
-TP8F)
JPTG1
M2_SRW1
JPME2
JMD1: M.2
PCI-E 3.0 X4 / I-SATA4
JD1
JTPM1
PRESS FIT
USB 2
JSAS1
L-SAS0-3
JSAS4
L-SAS12-15
PRESS FIT
PRESS FIT
FAN4
2-28
PCI Slot SMB Enable
Jumper Settings
Pin# Definition
1-2
2-3
PRESS FIT
JPL3:
LAN3/4/5/6
1-2:ENABLE
2-3:DISABLE
LAN 5/6 LAN 3/4
A A
C C
A A
C C
JPL1/JPL2:
LAN 7/8 LAN1/ LAN2
1-2:ENABLE 2-3:DISABLE
Intel Xeon
D-1500
SoC
A
JBT1:
CMOS
CLEAR
BT1
FAN3
LED3
JF1 JGP1
PWR
RST X FF
ON
Enabled
Disabled (Default)
A. Clear CMOS
B. JI C1
2
C. JI C2
2
IPMI_LAN
LAN 1/2
USB 0/1(3.0)
JPUSB1
JPV1
JPI2C1
JPW1
JPH1
JF1:
OH NIC2 HDD PWR
NIC1 LED
LED