Unit Identifier Switch - Supermicro X10SDV User Manual

Unit Identifier Switch

A Unit Identifier (UID) Switch and two LED
indicators are located on the motherboard. The
UID Switch is located next to the VGA port on
the back panel. The Rear UID LED (LED7) is
located next to the UID Switch. The Front Panel
UID LED is located at Pin 7 of the Front Control
Panel at JF1. Connect a cable to Pin 7 on JF1
for Front Panel UID LED indication. When you
press the UID switch, both Rear UID LED and
Front Panel UID LED Indicators will be turned
on. Press the UID switch again to turn off both
LED Indicators. These UID Indicators provide
easy identification of a system unit that may be
in need of service.
Note: UID can also be triggered via
IPMI on the motherboard. For more
information on IPMI, please refer to
the IPMI User's Guide posted on our
website at http://www.supermicro.
com.
JI2C1/JI2C2:
JBR1
1-2:ENABLE 1-2:NORMAL
BAR CODE
2-3:DISABLE 2-3:BIOS RECOVERY
JPG1:
1-2:ENABLE
2-3:DISABLE
JPS1:SAS
1-2:ENABLE
2-3:DISABLE
JWD1:WATCH DOG
1-2:RST
2-3:NMI JL1:
CHASSIS
INTRUSION
JOH1-OH
MP_SRW2
JIPMB1
BMC
AST2400
MP_SRW1
JMP1
PCI-E 2.0 X1 / I-SATA5
COM1
JLANLED1
JTGLED1
JOH1
LSI
A
2116
LEDS1
(-7TP4F/-7TP8F)
I-SATA3
JSAS4
JSAS3
L-SAS8-11 L-SAS12-15
I-SATA2
PRESS FIT PRESS FIT
A
B
LED7
A
C
UID
VGA
JPL3:
LAN3/4/5/6
M2_SRW3
1-2:ENABLE
2-3:DISABLE
C
LED8
PHY
10GbE
CS2447
A
C
LEDM1
M2_SRW2
i350
AM4
(-7TP8F/
-TP8F)
JPTG1
M2_SRW1
JPME2
JMD1: M.2
PCI-E 3.0 X4 / I-SATA4
JD1
JTPM1
PRESS FIT
USB 2
JSAS1
L-SAS0-3
PRESS FIT
LED3
FAN4
JF1
2-13
PRESS FIT
LAN 3/4
LAN 5/6
A
A
C C
A A
C C
JPL1/JPL2:
LAN 7/8 LAN1/ LAN2
1-2:ENABLE 2-3:DISABLE
Intel Xeon
D-1500
SoC
JBT1:
CMOS
CLEAR
BT1
FAN3
JGP1
JF1:
PWR OH NIC2 HDD
RST X FF NIC1 LED
ON
Chapter 2: Installation
UID Switch
Pin# Definition
1 Ground
2 Ground
3 Button In
4 Button In
UID LED
Status
Color/State Status
Blue: On Unit Identified
A. UID Switch
B. Rear UID LED
IPMI_LAN
LAN 1/2
USB 0/1(3.0)
JPUSB1
JPV1
JPI2C1
JPW1
JPH1
PWR
LED