Standard Default Setting - Toshiba TOSVERT VF-PS1 Instruction Manual

5.20

Standard default setting

: Factory default setting
• Function
This parameter is to set two or more parameters at a time for different commands. Using this parameter, all
parameters can be also return to their respective default settings by one operation, and save or set specific
parameters individually.
Title Function
Factory default
setting
Note 1: This parameter is used to change the settings of other parameters. Therefore,
Note 2: cannot be set during the inverter operating. Always stop the inverter first and then program.
Note 3: When parameter
Note 4: If is set to
used with the inverter. (The personal computer communications software PCM001Z cannot be used, either.)
Furthermore, the copy function of the LED extended panel option (RKP002Z) does not work normally, so use
only the parameter setting function and the monitoring function.
Note 5: If the power is turned off while the parameter
is turned back on. If the
[Programmed value]
50Hz default setting (
Setting at causes all the following parameters to be set for operation using a base frequency of 50Hz.
(This does not change the settings of any other parameters.)
• Base frequency 1
• Maximum frequency
• Upper limit frequency
• RR/S4 input point 2 frequency
• VI/II input point 2 frequency
• Base frequency 2
• RX input point 2 frequency
• AI1 input point 2 frequency
• AI2 input point 2 frequency
60Hz default setting (
Setting at causes all the following parameters to be set for operation using a base frequency of 60Hz.
(This does not change the settings of any other parameters.)
• Base frequency 1
• Maximum frequency
• Upper limit frequency
• RR/S4 input point 2 frequency
• VI/II input point 2 frequency
• Base frequency 2
• RX input point 2 frequency
• AI1 input point 2 frequency
• AI2 input point 2 frequency
Adjustment range
: –
:50Hz default setting
:60Hz default setting
:Factory default setting
:Trip clear
:Cumulative operation time cleared
:Initialization of type information
:Save user-defined parameters
:Reset of user-defined parameters
:Cumulative fan operation time record clear
:Acceleration/deceleration time setting 0.01 sec.~600.0 sec.
[Note 4]
:Acceleration/deceleration time setting 0.1 sec.~6000 sec.
:500V-50Hz default setting
:575V-60Hz default setting
:690V-50Hz default setting
is invoked, the value set previously is displayed on the left side of the parameter.
, the optional communication devices DEV002Z, PDP002Z and CCL001Z cannot be
error occurs, set
= )
: 50Hz • RP/high-speed pulse input point 2 frequency
: 50Hz • Commercial power/inverter switching frequency
: 50Hz • PID deviation upper limit
: 50Hz • PID deviation lower limit
: 50Hz • Process upper limit
: 50Hz • PID output upper limit
: 50Hz • Motor rated rotational speed
: 50Hz • Point 2 frequency
: 50Hz
= )
: 60Hz • RP/high-speed pulse input point 2 frequency
: 60Hz • Commercial power/inverter switching frequency
: 60Hz • PID deviation upper limit
: 60Hz • PID deviation lower limit
: 60Hz • Process upper limit
: 60Hz • PID output upper limit
: 60Hz • Motor rated rotational speed
: 60Hz • Point 2 frequency
: 60Hz
E-39
is always displayed.
is being set, an error ( ) will occur when the power
again.
:1400~1480min-1 (According to model)
:1680~1775min-1 (According to model)
E6581531
Default setting
5
: 50Hz
: 50Hz
: 50Hz
: 50Hz
: 50Hz
: 50Hz
: 50Hz
: 60Hz
: 60Hz
: 60Hz
: 60Hz
: 60Hz
: 60Hz
: 60Hz