Avaya G450 Configuration Manual page 5

customer and the customer's employees from gaining access to the
network and to these codes.
For equipment approved prior to July 23, 2001:
This equipment complies with Part 68 of the FCC rules. On either the
rear or inside the front cover of this equipment is a label that contains,
among other information, the FCC registration number, and ringer
equivalence number (REN) for this equipment. If requested, this
information must be provided to the telephone company.
For equipment approved after July 23, 2001:
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the Administrative Council on Terminal
Attachments (ACTA). On the rear of this equipment is a label that
contains, among other information, a product identifier in the format
US:AAAEQ##TXXX. If requested, this number must be provided to the
telephone company.
The REN is used to determine the quantity of devices that may be
connected to the telephone line. Excessive RENs on the telephone line
may result in devices not ringing in response to an incoming call. In
most, but not all areas, the sum of RENs should not exceed 5.0.
L'indice d'équivalence de la sonnerie (IES) sert à indiquer le nombre
maximal de terminaux qui peuvent être raccordés à une interface
téléphonique. La terminaison d'une interface peut consister en une
combinaison quelconque de dispositifs, à la seule condition que la
somme d'indices d'équivalence de la sonnerie de tous les dispositifs
n'excède pas cinq.
To be certain of the number of devices that may be connected to a line,
as determined by the total RENs, contact the local telephone company.
For products approved after July 23, 2001, the REN for this product is
part of the product identifier that has the format US:AAAEQ##TXXX.
The digits represented by ## are the REN without a decimal point (for
example, 03 is a REN of 0.3). For earlier products, the REN is
separately shown on the label.
Means of Connection:
Connection of this equipment to the telephone network is shown in the
following table:
Manufact FIC Code
urer's
Port
Identifier
Off OL13C
premises
station
DID trunk 02RV2.T
CO trunk 02GS2
02LS2
Tie trunk TL31M
Basic 02IS5
Rate
Interface
1.544 04DU9.B
digital N
interface
04DU9.1K
N
Configuring V.150.1 on Avaya G450 and G430 Branch Gateway
SOC/ Network
REN/A.S. Jacks
Code
9.0F RJ2GX,
RJ21X,
RJ11C
AS.2 RJ2GX,
RJ21X,
RJ11C
0.3A RJ21X,
RJ11C
0.3A RJ21X,
RJ11C
9.0F RJ2GX
6.0F, 6.0Y RJ49C
6.0F RJ48C,
RJ48M
6.0F RJ48C,
RJ48M
Manufact FIC Code
urer's
Port
Identifier
04DU9.1S
N
120A4 04DU9.D
channel N
service
unit
If this equipment causes harm to the telephone network, the telephone
company will notify you in advance that temporary discontinuance of
service may be required. But if advance notice is not practical, the
telephone company will notify the customer as soon as possible. Also,
you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
The telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the
equipment. If this happens, the telephone company will provide
advance notice in order for you to make necessary modifications to
maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty
information, please contact the Technical Service Center at 1-800-242-
2121 or contact your local Avaya representative. If the equipment is
causing harm to the telephone network, the telephone company may
request that you disconnect the equipment until the problem is
resolved.
A plug and jack used to connect this equipment to the premises wiring
and telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to
be connected to a compatible modular jack that is also compliant.
Connection to party line service is subject to state tariffs. Contact the
state public utility commission, public service commission or
corporation commission for information.
Installation and Repairs
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed
using an acceptable method of connection. The customer should be
aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be coordinated by a
representative designated by the supplier. It is recommended that
repairs be performed by Avaya certified technicians.
FCC Part 68 Supplier's Declarations of Conformity
Avaya Inc. in the United States of America hereby certifies that the
equipment described in this document and bearing a TIA TSB-168 label
identification number complies with the FCC's Rules and Regulations
47 CFR Part 68, and the Administrative Council on Terminal
Attachments (ACTA) adopted technical criteria.
Avaya further asserts that Avaya handset-equipped terminal
equipment described in this document complies with Paragraph 68.316
of the FCC Rules and Regulations defining Hearing Aid Compatibility
and is deemed compatible with hearing aids.
Copies of SDoCs signed by the Responsible Party in the U. S. can be
obtained by contacting your local sales representative and are
available on the following Web site: http://support.avaya.com/DoC.
Canadian Conformity Information
This Class A (or B) digital apparatus complies with Canadian ICES-003.
SOC/ Network
REN/A.S. Jacks
Code
6.0F RJ48C,
RJ48M
6.0Y RJ48C
May 2014 5