Frequency Characteristics; Sinewave Spectral Purity; Signal Characteristics - Agilent Technologies 33250A User Manual

WAVEFORMS
Standard Waveforms:
Arbitrary Waveforms
Waveform Length:
Amplitude Resolution:
Repetition Rate:
Sample Rate:
Filter Bandwidth:
Non-Volatile Memory:

FREQUENCY CHARACTERISTICS

Sine:
Square:
Ramp:
Pulse:
Noise (Gaussian):
Arb:
Resolution:
Accuracy (1 year):

SINEWAVE SPECTRAL PURITY

Harmonic Distortion
DC to 1 MHz:
1 MHz to 5 MHz:
5 MHz to 80 MHz:
Total Harmonic Distortion
DC to 20 kHz:
Spurious (non-harmonic)
DC to 1 MHz:
1 MHz to 20 MHz:
20 MHz to 80 MHz:
Phase Noise (30 kHz band)
10 MHz
80 MHz
8
Chapter 8 Specifications
Agilent 33250A Function / Arbitrary Waveform Generator
Sine, Square, Ramp,
Pulse, Noise, Sin(x)/x,
Exponential Rise,
Exponential Fall,
Negative Ramp,
Cardiac, DC Volts
1 to 64K points
12 bits (including sign)
1 µHz to 25 MHz
200 MSa/s
50 MHz
Four 64K waveforms
1 µHz to 80 MHz
1 µHz to 80 MHz
1 µHz to 1 MHz
500 µHz to 50 MHz
50 MHz bandwidth
1 µHz to 25 MHz
1 µHz;
except pulse, 5 digits
2 ppm, 18°C to 28°C
3 ppm, 0°C to 55°C
2
< 3 Vpp > 3 Vpp
-60 dBc -55 dBc
-57 dBc -45 dBc
-37 dBc -30 dBc
< 0.2% + 0.1 mVrms
3
-60 dBc
-50 dBc
-50 dBc + 6 dBc/octave
< -65 dBc (typical)
< -47 dBc (typical)
320

SIGNAL CHARACTERISTICS

Square Wave
Rise / Fall Time:
Overshoot:
Asymmetry:
Jitter (rms)
< 2 MHz:
> 2 MHz:
Duty Cycle
< 25 MHz:
25 MHz to 50 MHz:
50 MHz to 80 MHz:
Pulse
1
Period:
Pulse Width:
Variable Edge Time:
Overshoot:
Jitter (rms):
Ramp
Linearity:
Symmetry:
Arb
Minimum Edge Time:
Linearity:
Settling Time:
Jitter (rms):
_______________
1
A total of four waveforms can be stored.
2
Harmonic distortion at low amplitudes is limited by
a -70 dBm floor.
3
Spurious noise at low amplitudes is limited by
a -75 dBm floor.
4
Edge time decreased at higher frequency.
4
< 8 ns
< 5%
1% of period + 1 ns
0.01% + 525 ps
0.1% + 75 ps
20.0% to 80.0%
40.0% to 60.0%
50.0% (fixed)
20.00 ns to 2000.0 s
8.0 ns to 1999.9 s
5.00 ns to 1.00 ms
< 5%
100 ppm + 50 ps
< 0.1% of peak output
0.0% to 100.0%
< 10 ns
< 0.1% of peak output
< 50 ns to 0.5% of
final value
30 ppm + 2.5 ns