D To Send/Read Memory Contents - Icom IC-7000 Instruction Manual

17
CONTROL COMMAND
0E B0
B1
D0
D3
0F 00
01
10
11
12
10 00
01
02
03
04
05
06
07
08
09
10
11 —
13 00
01
02
14 01 + Level data [AF] level setting (0=max. CCW to
02 + Level data [RF] level setting (0=max. CCW to
03 + Level data [SQL] level setting (0=11 o'clock
06 + Level data NR level setting (0=min. to
07 + Level data Inside [PBT] setting or IF shift
08 + Level data Outside [PBT] setting
09 + Level data CW Pitch setting (0=300 Hz,
0A + Level data RF Power setting (0=mini. to
0B + Level data MIC Gain setting (0=mini. to
0C + Level data Key Speed setting (0=slow to
0D + Level data NOTCH (NF1) frequency setting
0E + Level data C O M P L eve l s e t t i n g ( 0 = 0 t o
0F + Level data Break-IN DELAY setting (0=2.0d
12 + Level data N B l e v e l s e t t i n g ( 0 = 0 t o
15 + Level data M o n i t o r g a i n s e t t i n g ( 0 = 0 t o
16 + Level data V O X g a i n s e t t i n g ( 0 = 0 t o
143
Set as non-select channel
Set as select channel
Set scan resume OFF
Set scan resume ON
Turn the split function OFF
Turn the split function ON
Select simplex operation
Select –DUP operation
Select +DUP operation
AM/FM/WFM modes:
Select 10 Hz tuning step
SSB/CW/RTTY modes: TS OFF
Select 100 Hz tuning step
Select 1 kHz tuning step
Select 5 kHz tuning step
Select 9 kHz tuning step
Select 10 kHz tuning step
Select 12.5 kHz tuning step
Select 20 kHz tuning step
Select 25 kHz tuning step
Select 100 kHz tuning step
AM/FM/WFM modes:
Select MHz step
SSB/CW/RTTY modes: Invalid
Select/read attenuator (0=OFF,
12=ON (12 dB))
Announce with voice synthesizer
(00=all data; 01=frequency and
S-meter level; 02=receive mode)
255=max. CW)
255=11 o'clock)
to 255=max. CW)
255=max.)
setting (0=max. CCW, 128=center,
255=max. CW)
( 0=max. CCW, 128=center,
255=max. CW)
128=600 Hz, 255=900 Hz, in 5 Hz
steps)
255=max.)
255=max.)
255=fast)
(0=low freq. to 255=high freq.)
255=10)
to 255=13.0d)
14 17 + Level data Anti-VOX gain setting (0=0 to
18 + Level data Contrast (LCD) setting (0=0 to
19 + Level data B r i g h t ( L C D ) s e t t i n g ( 0 = 0 t o
1A + Level data NOTCH (NF2) frequency setting
(0=low freq. to 255=high freq.)
15 01 Read squelch condition
02 Read S-meter level
11 Read RF power meter
12 Read SWR meter
13 Read ALC meter
14 Read COMP meter
16 02 Preamp (0=OFF; 1=ON)
12 AGC selection
(1=Fast; 2=Mid; 3=Slow)
22 Noise blanker (0=OFF; 1=ON)
40 Noise reduction (0=OFF; 1=ON)
41 Auto notch (0=OFF; 1=ON)
42 Repeater tone (0=OFF; 1=ON)
43 Tone squelch (0=OFF; 1=ON)
44 Speech compressor (0=OFF; 1=ON)
45 Monitor (0=OFF; 1=ON)
46 VOX function (0=OFF; 1=ON)
47 Break-in (0=OFF; 1=semi
break-in; 2=full break-in)
48 Manual notch (NF1) (0=OFF; 1=ON)
4B DTCS (0=OFF; 1=ON)
4C VSC (0=OFF; 1=ON)
4F Twin Peak Filter (0=OFF; 1=ON)
50 Dial lock function (0=OFF, 1=ON)
51 Manual notch (NF2) (0=OFF, 1=ON)
19 00 Read the transceiver ID
1A 00 Send/read memory contents (see
page 146 for details)
01 Send/read band stacking register
contents (see page 146 for details)
02 Send/read memory keyer contents
(see page 146 for details)
03 Send/read the selected filter width
( SSB, CW, RTTY:
0=50 Hz to 40/31=3600/2700 Hz;
AM: 0=200 Hz to 49=10 kHz)
04 Send/read the selected AGC time
constant (0=OFF, 1=0.1/0.3 sec.
to 13=6.0/8.0 sec.)
050001 RF Power setting (0=mini. to
255=max.)
050002 MIC Gain setting (0=mini. to
255=max.)
050003 Send/read of SSB TX bandwidth
(lower edge) for wide
(0=100, 1=200, 2=300, 3=500 HZ)
050004 Send/read of SSB TX bandwidth
(higher edge) for wide (0=2500,
1=2700, 2=2800, 3=2900 HZ)
050005 Send/read of SSB TX bandwidth
(lower edge) for middle
(0=100, 1=200, 2=300, 3=500 HZ)
050006 Send/read of SSB TX bandwidth
(higher edge) for middle (0=2500,
1=2700, 2=2800, 3=2900 HZ)