Receive And Transmit; Operating Ssb; D Convenient Functions For Receive - Icom IC-7000 Instruction Manual

4

RECEIVE AND TRANSMIT

q Push [
Y(
BAND
)]/[
band or push a band key on the HM-151.
w Push [MODE] momentarily or hold down for
1 second to select LSB or USB mode.
MHz USB is automatically selected.
e Rotate [DIAL] to tune in a desired signal.
signal is received.
r Rotate [AF] to set audio to a comfortable listening
level.
t Push [PTT] (microphone) to transmit.
[TX] indicator lights red.
y Speak into the microphone at your normal voice
level.
u Release [PTT] (microphone) to return to receive.
D
Push [P.AMP/ATT] momentarily to turn the
preamp ON or OFF.
" appears when the preamp is set to ON.
Holding down [P.AMP/ATT] for 1 second to turn
the attenuator ON.
[ P. A M P / AT T ] m o m e n t a r i l y t o t u r n t h e
attenuator OFF.
" appears when the attenuator is set to ON.
Push
or twice to select the twin PBT ON or OFF (M-ch
RIT).
selected.
Rotate
While "M -3 " is selected, push [F-3 A G C ]
momentarily one or more times to select AGC
fast, AGC middle and AGC slow.
[MENU/GRP] for 1 second once or twice
to select the menu group M.
[MENU/GRP] momentarily one or more times
to select the menu M-3.
," "
fast time constant, middle time constant and slow time
constant is selected, respectively.
While "M-3" is selected, hold down [F-3 AGC] for
1 second to enter the AGC Set mode.
[F-2 FAST], [F-3 MID] or [F-4 SLOW] to
select the time constant, then rotate [DIAL] to adjust
the time constant.
39
Z(
BAND
)] to select the desired
(p. 72)
(p. 77)
(switch) momentarily once
(controls–inner/outer).
CLR
)] to clear the settings.
(p. 74)
" and " " appears when the
[AF] [MODE] [TX] indicator
"LSB" or "USB" appears
(p. 78)
Push [NB/ADJ] to turn the noise blanker ON or
OFF.
" appears when the noise blanker is set to ON.
Hold down [NB/ADJ] for 1 second to enter the
noise blanker Set mode, then rotate [DIAL] to
adjust the threshold level, or noise pulse width.
(p. 79)
Push [NR/LEV] to turn the DSP noise reduction
ON or OFF.
" appears when the DSP noise reduction is ON.
Hold down [NR/LEV] for 1 second to enter the
DSP noise reduction level Set mode, then rotate
[DIAL] to adjust the DSP noise reduction level.
(pp. 80, 81)
Push [MNF/ADJ] to turn the manual notch filter
ON or OFF.
" appears when the manual notch filter is set to ON.
Hold down [MNF/ADJ] for 1 second to enter the
manual notch filter Set mode.
[F-2 NF1], [F-3 NF2] to select the notch filter,
push [F-4 NW] to set the filter width, rotate [DIAL] to
set the notch frequency.
(p. 80)
Push [ANF/• REC] to turn the auto notch filter
ON or OFF.
" appears when the auto notch filter is set to ON.
While "S-1" is selected, push [F-4 VSC] to turn
the VSC function ON or OFF.
" appears when VSC function is set to ON.
[ ]
[ ]
[DIAL]
(p. 82)