Error Code - Canon mf6600 Series Service Manual

Error Code

Display Detail
Main Cause/Symptom
Code Code
E000 0 Startup error
The temperature detected by the main
or sub thermistor does not rise to the
specified value during startup control.
E001 0 Abnormally high temperature (detected by main thermistor)
The main thermistor detected an
abnormally high temperature during
temperature control.
1 Abnormally high temperature (detected by sub thermistor)
The sub thermistor detected an
abnormally high temperature during
temperature control.
Low temperature during temperature control.
E002 0
The target temperature is not reached
during temperature control.
Abnormally low temperature (detected by main thermistor)
E003 0
After the temperature detected by
the main thermistor has reached the
specified value, it does not reach the
specified value during initial rotation.
Abnormally low temperature (detected by sub thermistor)
1
After the temperature detected by
the sub thermistor has reached the
specified value, it does not reach the
specified value during initial rotation.
E010 0 Main motor failure
The main motor is faulty.
E100 0 BD detection PCB failure
The BD detection PCB is faulty.
7
Error Codes > Error Code
Countermeasure
- Check the fixing film connector.
- Replace the fixing film unit.
- Replace the Engine controller PCB.
- Check the connector of the fixing film
unit.
- Replace the fixing film unit.
- Replace the Engine controller PCB.
- Check the connector of the fixing film
unit.
- Replace the fixing film unit.
- Replace the Engine controller PCB.
- Check the connector of the fixing film
unit.
- Replace the fixing film unit.
- Replace the Engine controller PCB.
- Check the connector of the fixing film
unit.
- Replace the fixing film unit.
- Replace the Engine controller PCB.
- Check the connector of the fixing film
unit.
- Replace the fixing film unit.
- Replace the Engine controller PCB.
- Check the connector of the main
motor.
- Replace the main motor.
- Replace the Engine controller PCB.
- Replace the laser scanner unit.
- Replace the Engine controller PCB.
7 Error Codes > Error Code
Display Detail
Main Cause/Symptom
Code Code
Flash ROM write/read error
E196 1
The write/read of Flash ROM in the
Main Controller Board is faulty.
PCL ROM write/read error
2
The write/read of PCL ROM in the Main
Controller Board is faulty.
E197 0 Printer engine communication error
Erroneous communication between
the Engine controller PCB and Main
Controller Board was detected.
Erroneous communication with optional cassette
E716 0
Disconnection of the optional cassette
was detected after power-on, detection
of normal connection to the optional
cassette, and start of communication.
E730 0 inside error of the Main Controller Board
(PDL system error)
The inside of the Main Controller Board is faulty.
Erroneous communication between controller and printer
E733 0
Cannot communicate with the printer at
startup.
CCU communication error
E736 0
The installed modem PCB is
incompatible.
Erroneous communication between controller and network board
E739 0
The installed network board is
incompatible.
E805 0 Fan failure
The fan is faulty.
7-2
Countermeasure
- Replace the Main Controller Board.
- Replace the Main Controller Board.
- Check the connectors of the Engine
controller PCB and Main Controller
Board.
- Replace the Engine controller PCB
for normal connection.
- Replace the Main Controller Board.
- Check the connectors of the optional
cassette PCB and Engine controller
PCB.
- Replace the optional cassette PCB
for normal connection.
- Replace the Engine controller PCB.
- Replace the Main Controller Board.
- Check the connectors of the Engine
controller PCB and Main Controller
Board for normal connection.
- Check the power supply of the
printer (Check whether initialization is
performed at startup).
- Replace the Engine controller PCB
or Main Controller Board.
- Check the connectors of the Main
Controller Board and modem.
- Replace the modem PCB.
- Replace the Main Controller Board.
- Replace the Main Controller Board.
- Check the fan connector.
- Replace the fan.
- Replace the Engine controller PCB.
7-2