Installation - GBC RollSeal Ultima 35 EZ load Instruction Manual

GBC5147 Ultima 35 EZLoad Ma-EU+ 05/11/29 12:45 PM
1 2
3b 4
6 7
8b 9
Page 3
Important Safety instructions
YOUR SAFETY AS WELL AS THE SAFETY OF OTHERS IS IMPORTANT TO
GBC. IN THIS INSTRUCTION MANUAL AND ON THE PRODUCT ARE
IMPORTANT SAFETY MESSAGES. READ THESE MESSAGES CAREFULLY.
THE SAFETY ALERT SYMBOL PRECEDES EACH SAFETY
MESSAGE IN THIS INSTRUCTION MANUAL.
ON THE PRODUCT YOU WILL FIND IMPORTANT SAFETY MESSAGES.
READ THESE MESSAGES AND INSTRUCTIONS CAREFULLY. SAVE THESE
INSTRUCTIONS FOR LATER USE.
THE FOLLOWING WARNINGS ARE FOUND ON THIS PRODUCT.
3a
This safety message means that you could be seriously hurt or killed if
you open the product and expose yourself to hazardous voltage.
5
This safety message means that you could be burned and your fingers
and hands could be trapped and crushed in the hot rollers. Clothing,
jewellery and long hair could be caught in the rollers and pull you into
them.
8a
This safety message means that you could cut yourself if you are not
careful.
WARNING: THE SAFETY ALERT SYMBOL PRECEDES
EACH SAFETY MESSAGE IN THIS INSTRUCTION
MANUAL. THIS SYMBOL INDICATES A POTENTIAL
PERSONAL SAFETY HAZARD THAT COULD HURT YOU OR
OTHERS, AS WELL AS CAUSE PRODUCT DAMAGE OR
PROPERTY DAMAGE.
WARNING: DO NOT ATTEMPT TO SERVICE OR REPAIR
THE LAMINATOR.
WARNING: DO NOT CONNECT THE LAMINATOR TO AN
ELECTRICAL SUPPLY OR ATTEMPT TO OPERATE THE
10
LAMINATOR UNTIL YOU HAVE COMPLETELY READ
THESE INSTRUCTIONS. MAINTAIN THESE
INSTRUCTIONS IN A CONVENIENT LOCATION FOR
FUTURE REFERENCE.
4
Important Safeguards
WARNING: FOR YOUR PROTECTION, DO NOT CONNECT
THE LAMINATOR TO ELECTRICAL POWER OR ATTEMPT
TO OPERATE UNTIL YOU READ THESE INSTRUCTIONS
COMPLETELY. KEEP OPERATING INSTRUCTIONS IN A
CONVENIENT LOCATION FOR FUTURE REFERENCE. TO
GUARD AGAINST INJURY, THE FOLLOWING BASIC
SAFETY PRECAUTIONS MUST BE OBSERVED IN THE
SET-UP AND USE OF THE LAMINATOR.
General safeguards
WARNING
• Use this laminator only for its intended purposes as according to the
specifications outlined in the operating instructions.
Electrical shock hazard.
• Keep hands, long hair, loose clothing and articles such as necklaces
Do not open. No user
or ties away from the front of the pull rollers to avoid entanglement
serviceable parts inside.
and entrapment.
Refer servicing to qualified
service personnel.
• Avoid contact with the heat shoes during operation or shortly after
the laminator has been turned off. The heat shoes can reach
temperatures in excess of 148.9ºC.
• Keep hands and fingers away from the path of the sharp film cutter
blade located at the film exit.
CAUTION
• Do not place the laminator on an unstable cart, stand or table. An
HOT ROLLS. unstable surface may cause the laminator to fall resulting in serious
bodily injury. Avoid quick stops, excessive force and uneven floor
PINCH POINT.
surfaces when moving the laminator on a cart or stand.
Keep hands and
• Do not defeat or remove electrical and mechanical safety equipment
clothing away.
such as interlocks, shields and guards.
• Do not insert objects unsuitable for lamination.
• Do not expose laminator to liquids.
Electrical safeguards
CAUTION
SHARP BLADE. • This laminator must be connected to a supply voltage corresponding
to the electrical rating as indicated on the serial plate located on the
Keep hand and
rear of the machine.
fingers away.
• Unplug the laminator before moving it, or when it is not in use for an
extended period of time.
• Do not operate the laminator with a damaged power supply cord or
plug.
• Do not overload electrical outlets as this can result in fire or shock.
• Do not alter the attachment plug. This plug is configured for the
appropriate electrical supply.
• The unit is intended for indoor use only.
CAUTION: The receptacle must be located near the equipment
and easily accessible. Do not use an extension cord.
• Disconnect the attachment plug from the receptacle to which it is
connected and keep the power supply cord in your possession while
moving the laminator.
• Do not operate the laminator with a damaged power supply cord or
attachment plug, upon occurrence of a malfunction, or after
laminator has been damaged. Contact an authorised GBC service
representative for assistance.
Service
Perform only the routine maintenance procedures referred to in these
instructions.
Do not attempt to service or repair the laminator.
Unplug the unit and contact an authorised GBC service representative
for any required repairs or one or more of the following has occurred:
• The power supply cord or attachment plug is damaged.
• Liquid has been spilled into the laminator.
• The laminator is malfunctioning after being mishandled.
• The laminator does not operate as described in these instructions.
WARNING: THIS IS NOT A TOY - DO NOT ALLOW CHILDREN TO OPERATE THIS LAMINATOR!

Installation

• Shipping damage should be brought to the immediate attention of the • The laminator should be positioned to allow exiting film to drop freely
delivering carrier. to the floor. Accumulation of laminate as it exits the laminator may
cause film to wrap around the rollers, causing a jammed condition.
• Place the laminator on a stable flat surface capable of supporting
20kgs. The surface should be at least 76.2cm high to assure • Avoid placing laminator near sources of heat or cold. Avoid locating
comfortable positioning during operation. All four rubber feet should the laminator in the direct path of forced, heated or cooled air.
be on the supporting surface.
• Connect power cord to an appropriate power source. Avoid
connecting other equipment to the same branch circuit to which the
laminator is connected as this may cause nuisance tripping of the
circuit breaker or blown fuses.
Caring for the Ultima 35 EZload
The only maintenance required by the operator is to periodically clean
Remove the film from the laminator following the procedure
1
the heat shoes. The following procedure will help keep the heat shoes
outlined in the section FILM LOADING AND THREADING.
free of adhesive that has been deposited along the edge of the
laminating film. 2 Preheat the laminator until the READY LAMP (
CAUTION: THE FOLLOWING PROCEDURE IS PERFORMED 3 Clean the top and bottom heat shoes with a soft cloth.
WHILE THE LAMINATOR IS HOT. USE EXTREME
Follow the procedure in section FILM LOADING AND THREADING,
4
CAUTION.
Method Using Film Threading Card to reload the laminator.
WARNING: Do not apply cleaning fluids or solvents to
NOTE: Do not use metal scouring pads to clean the heat shoes!
the rollers.
WARNING: Do not laminate glitter and/or metallic items. Damage to the
WARNING: Do not attempt to laminate adhesives
rollers may result.
marked 'Flammable'.
) illuminates.
5