Espresso Machine - Breville BES840XL Instruction Booklet

oPERAtInG PAGE hEAdER.....
BEfoRE fIRSt USE
Machine Preparation
Remove and discard all labeling and
packaging materials attached to your
espresso machine. Ensure you have
removed all parts and accessories before
discarding the packaging.
Remove the water tank located at the
back of the machine by lifting the water
tank handle. Remove the plastic bag
containing the water filter and water
filter holder. Clean parts and accessories
(water tank, portafilter, filter baskets,
frothing jug) using warm water and
a gentle dish washing liquid, then
rinse and dry thoroughly. Wipe the
outer housing and drip tray with a soft
damp cloth and dry thoroughly. Do not
immerse the outer housing, power cord or
power plug in water or any other liquid.
notE
Do not use abrasive cleansers,
pads or cloths which can scratch
the surface. Do not clean any of
the parts or accessories in the
dishwasher.
1 2 3
Soak water filter for 5 mins Rinse water filter & mesh Place filter into filter holder
12
CondItIonInG thE WAtER
fILtER
• Remove the water filter and water
filter holder from the plastic bag.
• Soak the water filter in a cup of water
for 5 minutes, then rinse under cold
running water.
• Wash the water filter holder with cold
water, taking specific care to rinse the
stainless steel mesh.
• Insert the water filter into the two
parts of the water filter holder.
• Set Date Dial 2 months ahead.
• To install the assembled water filter
holder into the water tank, align the
base of the water filter holder with the
adapter inside the water tank. Push
down to lock into place.
• Slide the water tank back into
position at the back of the machine,
ensuring to push down completely to
lock into place.
notE
To purchase water filters contact
Breville Consumer Service on
1-866-273-8455 (USA) or
1-855-683-3535 (Canada).
4 5 6
REPLACEMENT DUE
Set date 2 months ahead Install filter in water tank Insert & lock water tank
PAGE hEAdER..... oPERAtInG
fIRSt USE
Initial Start Up
• Ensure the water filter is securely
fitted inside the water tank.
• Fill the water tank with cold,
preferably filtered water up to the
MAX mark. When replacing the
water tank, ensure to push down
completely to lock into place.
notE
Always check the water level
before use and replace water daily.
Use cold, preferably filtered water.
Do not use mineral or distilled
water or any other liquid.
• Plug the power cord into a 110/120V
power outlet.
• Press the POWER button to switch
the machine On. The POWER button
light will flash while the machine is
heating.
• A pumping sound will be heard. This
is normal.
• When the machine has reached
the correct operating temperature,
the POWER button light will stop
flashing and all button lights on the
control panel will illuminate. The
machine is now in STANDBY mode,
ready for the next step 'Flushing The
Machine'.
flushing the Machine
It is recommended to complete a water
flushing operation, without ground
coffee, to ensure the machine has been
conditioned.
When the machine has reached
STANDBY mode, run the following 2
steps:
Press 2 CUP button to run hot water
1.
through the group head.
Rotate the STEAM/HOT WATER
2.
dial
to the HOT WATER position and
run for
10 seconds.
Repeat this cycle until the water tank
is empty.
STEAM STANDBY HOT WATER
GEnERAL oPERAtIon
Preset Shot volume - 1 CUP button
Press the 1 CUP button once to extract
a single shot of espresso at the preset
volume (approx. 1oz / 30ml). The
extraction will start using the low
pressure pre-infusion (see page 14). The
machine will stop after the preset volume
has been extracted.
13