Emotron VS30 Manuals

Emotron VS30 Manuals

Manuals and User Guides for Emotron VS30. We have 3 Emotron VS30 manuals available for free PDF download: Operation Instructions Manual, Instruction, Mounting And Switch On Instruction

Emotron VS30 Operation Instructions Manual

Emotron VS30 Operation Instructions Manual (528 pages)

Brand: Emotron | Category: Controller | Size: 8 MB

Table of Contents

Table of Contents
3
General Information

13
- Read First, then Start
  13
Safety Instructions

14
- Basic Safety Measures
  14
- Residual Hazards
  15
- Application as Directed
  15
Mounting

16
- Important Notes
  16
- Electrical Installation
  17
  - 1-Phase Mains Connection 230/240 V
    17
    
    Connection Plan
    17
    
    Fusing and Terminal Data
    18
  - 1/3-Phase Mains Connection 230/240 V
    20
    
    Connection Plan
    20
    
    Fusing and Terminal Data
    21
  - 3-Phase Mains Connection 400 V
    23
    
    Connection Plan
    23
    
    Fusing and Terminal Data
    24
  - 3-Phase Mains Connection 480 V
    27
    
    Connection Plan
    27
    
    Fusing and Terminal Data
    28
  - Canopen/Modbus RTU
    31
Commissioning

32
Diagnostics and Fault Elimination

74
- LED Status Display
  74
- Diagnostics Parameter
  75
  - Logbook
    76
  - Error History Buffer
    77
  - Inverter Diagnostics
    81
  - Network Diagnostics
    85
    
    Canopen Diagnostics
    86
    
    Modbus Diagnostics
    89
  - Diagnostics of the Inputs and Outputs
    90
    
    Digital Inputs and Outputs
    90
    
    Analog Inputs and Outputs
    91
  - Wireless-LAN Diagnostics
    93
  - Setpoint Diagnostic
    94
  - Process Controller Status
    95
  - Sequencer Diagnostics
    96
  - Device Identification
    97
  - Device Overload Monitoring (I*T)
    98
  - Heatsink Temperature Monitoring
    99
  - Life-Diagnosis
    99
- Error Handling
  100
  - Error Types
    100
  - Error Configuration
    101
  - Error Reset
    101
  - Keypad Error Messages
    102
- Data Handling
  103
Basic Setting

106
- Mains Voltage
  106
- Control Source Selection
  108
- Selection of Setpoint Source
  109
  - Keypad Setpoint Default Setting
    113
- Starting/Stopping Performance
  114
  - Starting Performance
    114
  - Stopping Performance
    116
- Frequency Limits and Ramp Times
  117
- Quick Stop
  120
- S-Shaped Ramps
  122
- Optical Device Identification
  123
Motor Control

124
- Motor Data
  125
  - Manual Setting of the Motor Data
    125
- Motor Control Selection
  126
- Optimisation of Motor Control
  141
  - V/F Voltage Boost
    142
  - Skip Frequencies
    143
  - Optimising the Stalling Behaviour
    145
  - Slip Compensation
    147
  - Oscillation Damping
    149
  - Synchronous Motor: Pole Position Identification (PPI)
    150
    
    Pole Position Identification (PPI) Without Movement
    151
- Optimisation of the Control Loops
  152
  - Options for Optimized Motor Tuning
    155
    
    Tuning of the Motor and the Speed Controller
    156
    
    Automatic Motor Identification (Energized)
    157
    
    Automatic Motor Calibration (Non-Energized)
    158
  - Inverter Characteristics
    159
  - Motor Equivalent Circuit Diagram Data
    160
  - Motor Controller Settings
    161
    
    Current Controller
    161
    
    Field Controller
    161
    
    Field Weakening Controller
    162
    
    Field Weakening Controller (Advanced)
    162
    
    Imax Controller
    163
    
    Flying Restart Controller
    164
    
    SLVC Controller
    164
    
    Torque Control W/ Freq. Limit
    165
    
    Slip Controller
    169
  - 7Speed Controller
    170
- Motor Rotating Direction
  171
- Switching Frequency Changeover
  172
- Motor Protection
  173
  - Motor Overload Monitoring (I²*T)
    173
    
    Speed Compensation for Protecting Motors at Low Speed
    175
  - Current Limits
    177
  - Overcurrent Monitoring
    179
  - Motor Phase Failure Detection
    180
  - Motor Speed Monitoring
    181
  - Motor Torque Monitoring
    182
Configuring the Network

183
- General Network Settings
  184
- Predefined Process Data Words
  202
  - Device Profile Cia 402
    203
  - AC Drive Profile
    204
    
    Customer Specific Configurations
    205
  - Further Process Data
    206
- Parameter Access Monitoring (PAM)
  211
- Acyclic Data Exchange
  212
- Canopen
  213
  - Canopen Introduction
    213
  - Canopen Node Address
    214
  - Canopen Baud Rate
    214
    
    Canopen Initialisation
    215
  - Canopen Diagnostics
    216
  - Canopen Emergency Telegram
    217
  - Canopen Heartbeat Protocol
    217
  - Canopen Process Data Objects
    219
  - Canopen Data Mapping
    224
  - Canopen Service Data Objects
    227
  - Canopen Error Responses
    229
  - Canopen Diagnostic Counter
    230
  - Canopen LED Status Displays
    231
  - Resetting the Canopen Interface
    232
  - Canopen Short Setup
    233
- Modbus RTU
  236
  - Modbus RTU Introduction
    236
  - Modbus RTU Node Address
    236
  - Modbus RTU Baud Rate
    237
  - Modbus RTU Data Format
    238
  - Modbus RTU Time-Out Monitoring
    238
  - Modbus RTU Diagnostics
    238
  - Modbus RTU Function Codes
    241
  - Modbus RTU Data Mapping
    242
  - Modbus RTU LED Status Displays
    246
  - Reset Modbus RTU Interface
    246
  - Modbus RTU Response Time
    246
  - Short Setup of Modbus RTU
    247
Configuring the Process Controller

249
- Basic Process Controller Settings
  250
- Process Controller Idle State and Rinse Function
  256
  - Process Controller Idle State
    256
  - Process Controller Rinse Function
    257
Additional Functions

258
- Device Commands
  259
  - Reset Parameters to Default
    259
  - Details
    259
  - Saving/Loading the Parameter Settings
    260
    
    Device Commands for Parameter Change-Over
    263
  - Delete Logbook
    264
- Keypad
  265
  - Keypad Language Selection
    265
  - Keypad Setpoint Increment
    265
  - Keypad Scaling of Speed Display
    265
  - Keypad Status Display
    265
  - Keypad Configuration of R/F and CTRL Buttons
    266
- Wireless LAN (WLAN)
  269
- DC Braking
  278
  - Example 1: Automatic DC Braking When the Motor Is Started
    280
  - Example 2: Automatic DC Braking When the Motor Is Stopped
    281
- Brake Energy Management
  283
  - Stopping the Deceleration Ramp Function Generator
    284
  - Inverter Motor Brake
    285
- Load Loss Detection
  286
- Access Protection
  287
  - Write Access Protection
    287
    
    Write Access Protection in the »Emotron Easy Starter
    289
    
    Write Access Protection in the Keypad
    292
    
    Configuring the Write Access Protection with the Keypad
    293
- Favorites
  296
- Parameter Change-Over
  302
  - Example: Selective Control of Several Motors with One Inverter
    313
- Device Profile Cia 402
  315
- Holding Brake Control
  318
  - Basic Setting
    319
  - Automatic" Brake Mode (Automatic Operation)
    320
  - Brake Holding Load
    322
    
    General Mode of Operation
    323
  - Brake Closing Level
    324
  - Manual Release of the Holding Brake
    326
- Flying Restart Circuit
  327
- Timeout für Fault Reaction
  329
- Automatic Restart
  330
- Mains Failure Control
  331
  - Activating the Mains Failure Control
    333
  - Restart Protection
    334
  - Fast Mains Recovery
    334
  - Commissioning the Mains Failure Control
    335
- Process Data
  336
  - Position Counter
    336
- Firmware Download
  337
  - Firmware Download with »Emotron Easy Starter (Firmware Loader)
    337
- Additive Voltage Impression
  338
  - Example: Using the Function with a 400-V Inverter
    339
- Parameter for Engineering Tools
  340
Sequencer

343
- Segment Configuration
  346
- Sequence Configuration
  356
- Sequencer Basic Settings
  371
Flexible I/O Configuration

374
- Control Source Change-Over
  375
  - Example 1: Change-Over from Terminal Control to Keypad Control
    378
  - Example 2: Change-Over from Terminal Control to Network Control
    379
- Start / Stop Motor
  380
- Setpoint Change-Over
  396
  - Priority of the Setpoint Sources
    398
  - Analog Input Setpoint Source
    398
  - Keypad Setpoint Source
    401
  - Network Setpoint Source
    403
  - Setpoint Source of Preset Setpoints
    404
  - Motor Potentiometer Setpoint Source (MOP)
    409
  - Setpoint Source Segment Setpoints
    413
- Reset Error
  415
- Activating DC Braking Manually
  417
- Releasing Holding Brake Manually
  419
- Activating Ramp 2 Manually
  421
- Triggering a User-Defined Fault
  423
- Functions for Parameter Change-Over
  424
- Process Controller Function Selection
  433
- Sequencer Control Functions
  436
- Frequency Threshold for "Frequency Threshold Exceeded" Trigger
  441
- Configuration of Digital Inputs
  443
- Configuration of Analog Inputs
  444
  - Analog Input 1
    444
    
    Example 1: Input Range 0
    446
    
    Example 2: Input Range 0
    446
    
    Example 3: Error Detection
    447
  - Analog Input 2
    448
- Configuration of Digital Outputs
  450
  - Relay
    450
  - Digital Output 1
    454
  - Networdout1 Status Word
    454
- Configuration of Analog Outputs
  459
  - Analog Output 1
    459
    
    Example 1: Output Voltage 0
    461
    
    Example 2: Output Voltage 2
    461
Technical Data

462
- Standards and Operating Conditions
  462
  - Protection of Persons and Device Protection
    462
  - EMC Data
    462
  - Motor Connection
    462
  - Environmental Conditions
    463
  - Electrical Supply Conditions
    463
- 1-Phase Mains Connection 230/240 V
  464
  - Rated Data
    464
- 1/3-Phase Mains Connection 230/240 V
  465
  - Rated Data
    465
- 3-Phase Mains Connection 400 V
  466
  - Rated Data
    466
- 3-Phase Mains Connection 480 V
  468
  - Rated Data
    468
Appendix

470
- Operate and Parameterise the Inverter with Keypad
  470
  - Keypad Operating Mode
    471
    
    Keypad Status Display
    471
    
    Function of Keypad Keys in Operating Mode
    472
    
    Error Reset with Keypad
    473
  - Keypad Parameterisation Mode
    474
    
    Parameter Groups
    474
    
    Function of the Keypad Keys in the Parameterisation Mode
    475
    
    Save Parameter Settings with Keypad
    476
    
    Display of Status Words on Keypad
    477
- Error Codes
  478
- Parameter Attribute List
  488

Advertisement

Emotron VS30 Mounting And Switch On Instruction

Emotron VS30 Mounting And Switch On Instruction (26 pages)

AC drive

Brand: Emotron | Category: DC Drives | Size: 0 MB

Table of Contents

Table of Contents
3
1 General Information

5
- First Read, then Start
  5
- Notations and Conventions
  5
  - Product Code
    5
2 Safety Instructions

6
3 Product Description

8
4 Mounting

9
- Important Notes
  9
- Mechanical Installation
  10
- Electrical Installation
  12
  - Connection to the 400 V System
    12
    
    Connection Plan
    12
    
    Fuses and Cable Cross-Sections
    13
    
    Terminal Data
    13
  - Connection to the IT System
    15
  - Canopen Connection
    16
    
    Connection Plan
    16
    
    Terminal Data
    16
    
    Basic Network Settings
    16
  - Modbus Connection
    17
    
    Connection Plan
    17
    
    Terminal Data
    17
    
    Basic Network Settings
    17
  - Connection of the Safety Module
    18
    
    Important Notes
    18
    
    Connection Plan
    19
    
    Terminal Data
    19
5 Commissioning

20
6 Technical Data

23
- Standards and Operating Conditions
  23
- Rated Data
  25
  - Connection to the 400 V System
    25

Emotron VS30 Instruction

Emotron VS30 Instruction (34 pages)

Brand: Emotron | Category: Controller | Size: 1 MB

Table of Contents

General Information
5
Safety Instructions
6
Residual Hazards
7
Product Description
8
Mounting
9
Mechanical Installation
10
Electrical Installation
13
Phase Mains Connection 230/240 V
14
Fusing and Terminal Data
16
Phase Mains Connection 230/240 V
17
Fusing and Terminal Data
19
Phase Mains Connection 480 V
20
Fusing and Terminal Data
22
Canopen/Modbus
23
Commissioning
24
Initial Switch-On / Functional Test with Terminal Control
25
Technical Data
27
Phase Mains Connection 230/240 V
29
Phase Mains Connection 230/240 V
30
Phase Mains Connection 480 V
31

Advertisement

Advertisement

Related Products

Emotron Categories

DC Drives Controller Inverter Control Unit Servo Drives

More Emotron Manuals