Selecting Operation; Room Temperature Adjustment; Time Setting; Timer Setting - Mitsubishi Electric PFD-P250VM-E Operation Manual

3.2. Selecting operation

When selecting operation
1. Press the 3 3 3 3 3 [selecting operation] button
Consecutive press of the selecting operation button switches the operation
over to E "
," " ," " ," (" "), and ("
check the display.
For cooling
Press the 3 3 3 3 3 [selecting operation] button and bring up the "
For dry
Press the 3 3 3 3 3 [selecting operation] button and bring up the " " display.
• The indoor fan turns to the low-speed operation, disabling the change of fan
speed.
Dry operation cannot be carried out at a room temperature of less than 18 °C.
•
For fan
Press the 3 3 3 3 3 [selecting operation] button and bring up the "
• The fan operation functions to circulate the air in the room.
• The temperature of the room cannot be set by fan operation.
Caution:
Never expose your body directly to cool air for a long time. Excessive expo-
sure to cool air is bad for your health, and should therefore be avoided.
Dry operation
The dry is a microcomputer-controlled dehumidifying operation which controls ex-
cessive air-cooling according to the room temperature of your choice. (Not usable
for heating.)
1. Until reaching room temperature of your choice
The compressor and indoor fan function is linked motion according to the change
of the room temperature and automatically repeat ON/OFF.
2. When reaching room temperature of your choice
Both the compressor and indoor fan stop.
When stop continues for 10 minutes, the compressor and indoor fan are oper-
ated for 3 minutes to keep the humidity low.
For heating
Press the 3 3 3 3 3 [selecting operation] button to bring up the "
Regarding displays during heating operation
"DEFROST"
Displayed only during the defrosting operation.
"STAND BY"
Displayed from the start of heating operation until the moment warm air blows out.
Caution:
• When the air conditioner is used together with burners, thoroughly ven-
tilate the area. Insufficient ventilation can result in accidents due to oxy-
gen deficiency.
• Never place a burner at a place where it is exposed to the airflow from the
air conditioner.
Doing so can result in imperfect combustion of the burner.
• The microcomputer functions in the following cases:
• Air does not blow out when heating starts.
- To prevent any cool air from escaping, the indoor fan is gradually switched in
sequence from faint airflow/weak airflow/set airflow according to the tem-
perature rise of the blown out air. Wait a moment until the airflow comes out
naturally.
• The fan is not moving at the set speed.
- In some models, the system switches over to faint airflow when the tempera-
ture of the room reaches the set temperature. In other cases, it stops to
prevent any cool air from escaping during the defrosting operation.
• Air flows out even if operation is stopped.
- Approximately 1 minute after the stop of operation, the indoor fan sometimes
rotates to eliminate extra heat generated by the electric heater, etc. The fan
speed changes to low or high.
• Heating can be used only by indoor warming-up.

3.3. Room temperature adjustment

To change room temperature
Press the 1 1 1 1 1 [room temperature adjustment] button and set the room tem-
perature of your choice.
once changes the setting by 1 °C.
Pressing or
If the pressing is continued, the setting continues to change by 1 °C.
• Indoor temperature can be set within the following range.
Cooling/dry: 14 - 30 °C (19 - 30 °C : Inlet temperature control)
Heating: 17 - 28 °C
• It is impossible to set the room temperature by the air-blow operation.
"). For the contents of operation,
" display.
" display.
" display.
The range of room temperature display is 8 - 39 °C. Outside this range, the
*
display flashes either 8 - 39 °C to inform you if the room temperature is lower or
higher than the displayed temperature.

3.4. Time setting

• Set the current time after turning ON the power of the unit or after restoration
from a power failure.
• It can be set regardless of the operation of the indoor unit.
• During the time operation, the time-setting button becomes void, disabling time
setting.
1. Press the 4 4 4 4 4 [time selection] button and bring up the A A A A A "current time"
display
• Every time it is pressed, the display changes.

"current "timer start
ON
CLOCK

time" time"
Caution:
When the current time is not yet set, the "CLOCK (current time)" display
flashes, disabling the setting of timer operation.
2. Set the current time by pressing the 4 4 4 4 4
The time cannot be set while the C "timer on" is displayed.
•
While the A "CLOCK" time is displayed, press the time setting 4
•
buttons and set the time.
• The setting advances one minute every time the 4
once, and retrogresses one minute every time the 4
once.
When respective 4 /
display goes fast forward. It advances in the order of 1 minute unit - 10 minute
unit - one hour unit.
About 10 seconds after the button operation has been completed, the C "cur-
•
rent time" and A "CLOCK" displays disappear.
Caution:
• Remote controller is equipped with a simplified clock with a precision of
about + or - one minute per month.
• The time must be readjusted (reset) every time the unit is subjected to a
power stop of the unit or a power failure.

3.5. Timer setting

• If the timer is set, the unit starts (stops) at the set time, and the time mode is
terminated.
When you wish to confirm the starting and ending time, press the 4 [time
•
selection] button while C "
" is displayed.
Function of timer
On-timer
Set the on-timer for the time the working day begins in your company.
When the set start time arrives, the unit starts operation.
Off-timer
Use the off-timer as a reminder to turn off the unit. When the set end-work time
arrives, the unit stops operation.
There are three methods for using the timer.
1. ON/OFF Timer When setting both starting and ending time
2. On-timer When only setting the starting time
(Ending time is set to " - - : - - ")
3. Off-timer When only setting the ending time
(Starting time is set to " - - : - - ")
Display example of timer setting
ON OFF
The example shows a timer set for operation start at 8:00 and end at 17:00.
1. Press the 2 2 2 2 2 [timer/continuous] button and bring up the C C C C C no display
2. Press the 4 4 4 4 4 [time selection] button and bring up the A A A A A "Timer start time"
display
3. Press the 4 4 4 4 4 ) button of the 4 4 4 4 4 [time selection] and set the
(
starting time
When using it as an off-timer, set the starting time to " - - : - - ".
The " - - : - - " is displayed next to 23:50.
4. Press the 4 4 4 4 4 [time selection] button and bring up the A A A A A "Timer end time"
display


"timer end
OFF
(no display)
 
time"
or button
/
button is pressed
button is pressed
buttons are pressed continuously, the time
ON OFF
7