Thermogroup 5240 Thermotouch 4.3iC Manual

Thermogroup 5240 Thermotouch 4.3iC Manual

Hide thumbs Also See for 5240 Thermotouch 4.3iC:

Advertisement

5240IG
5240
Thermotouch 4.3iC
®
Colour Touchscreen Thermostat
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 5240 Thermotouch 4.3iC and is the answer not in the manual?

Questions and answers

Summary of Contents for Thermogroup 5240 Thermotouch 4.3iC

  • Page 1 5240IG 5240 Thermotouch 4.3iC ® Colour Touchscreen Thermostat ®...
  • Page 2 Introduction 5240IG Thermotouch 4.3iC thermostat ® Thermotouch 4.3iC is a digital thermostat, which is designed for electric floor ® heating systems with a maximum load of up to 16A (3600W). Thermotouch 4.3iC features a 4.3” Intelligent Control Truetouch colour display and 4 ®...
  • Page 3: Installation

    Installing Thermotouch 4.3iC ® 5240IG Before you begin A sensor conduit and deep back box must be installed to continue this installation. Feed the provided sensor probe (3m) down through the sensor conduit into a representive area of the floor. For any technical advice or questions visit our website, www.thermogroupuk.com or call our technical team on 0800 019 5899.
  • Page 4 Wiring Thermotouch 4.3iC ® 5240IG Wire and replace face plate Loosen the tension screws to allow the wires to be inserted and fixed. Position the cables as shown in the wiring diagram and 3600W/16A 230V/AC Sensor ensure each screw is Ensure system is correctly earthed.
  • Page 5 ® Programming Thermotouch 4.3iC 5240IG Thermotouch 4.3iC interface ® ROOM On / Off button Heating icon Mode button Weekday icon Menu button Ambient temperature Down button Clock icon Up button Temperature icon Mode icon Floor temperature Set temperature Mode icon area FREEPHONE 0800 019 5899...
  • Page 6: Preset Modes

    ® Programming Thermotouch 4.3iC 5240IG Preset Modes Manually switch between these preset temperature modes to allow flexibility outside of your heating schedule. Economy mode Holiday mode Preset a low energy saving Automatically maintain a preset temperature 18C for economical low energy saving temperature comfort and energy savings.
  • Page 7: Schedule Settings

    ® Programming Thermotouch 4.3iC 5240IG Schedule settings Press MENU Button, then press review your weekly schedule. Select Mon - Fri, Sat or Sun to edit your custom heating schedule. RETURN Example: if you would like to edit your Sunday schedule, press Sun column to enter the edit page as shown.
  • Page 8: Language Select

    ® Programming Thermotouch 4.3iC 5240IG Edit time & date Press MENU button, then button to edit date and time with buttons. Press APPLY to save the changes. RETURN Mode pre-set temp. Press MENU button, then button to select a mode. Now edit that modes temperature with buttons.
  • Page 9: Protection Settings

    ® Programming Thermotouch 4.3iC 5240IG Protection settings Press MENU then button to enter protection settings page. You can set Over Protection temperature & Low Protection temperature with the buttons. Press APPLY to save the changes. RETURN High protection: This is an Over Heat Protection setting designed to monitor the floor temperature and limit it to a level set by you.
  • Page 10: Parameter Settings

    ® Programming Thermotouch 4.3iC 5240IG Parameter settings To access parameter settings switch Thermotouch 4.3iC OFF and ® immediately press for 2 seconds. You can set the desired values by pressing << or >> , and go to other pages by pressing PRE or NEXT. Please note the upper limit should be no higher than 28 C to conform with European regulations.
  • Page 11: Technical Specification

    Technical specification 5240IG Dimensions 60mm 19mm 31mm 94mm 4.3” 130mm FREEPHONE 0800 019 5899...
  • Page 12: Product Features

    • Maximum load: 16A (3600W) Paddock Wood, Kent. TN12 6DQ • Temperature range: 5~35 www.thermogroupuk.com • Ambient: 0~50 sales@thermogroupuk.com • Sensor: NTC10k, 10kΩ at 25 0800 019 5899 • Accuracy: ± 0.5 ® E&OE ©Thermogroup UK 2013 0800 019 5899...

Table of Contents