Hisense MST6E16JS Service Manual
  1. Manuals
  2. Brands
  3. Hisense Manuals
  4. LCD TV
  5. MST6E16JS
  6. Service manual
Hisense MST6E16JS Service Manual

Hisense MST6E16JS Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Liquid Crystal Display Television

Service Manual

Chassis： MST6E16JS
Product Type：LCD24V88APAM
Ver 1.0
Hisense Electric Co.，Ltd.
May， 2012

Advertisement

Table of Contents
loading

Related Manuals for Hisense MST6E16JS

Summary of Contents for Hisense MST6E16JS

  • Page 1: Service Manual

    Liquid Crystal Display Television Service Manual Chassis： MST6E16JS Product Type：LCD24V88APAM Ver 1.0 Hisense Electric Co.，Ltd. May， 2012...

  • Page 2: Table Of Contents

    Contents Contents................................- 2 - Service Manual ..............................- 2 - 1. Precautions and notices..........................- 3 - 1.1 WARNING ............................- 4 - 1.2 NOTES ............................- 7 - 2. Factory/Service OSD Menu and Adjustment...................- 10 - 2.1 To enter the Factory OSD Menu ....................- 10 - 2.2 Factory OSD Menu........................- 10 - 3.

  • Page 3: Precautions And Notices

    WHEN REPLACEMENT PARTS ARE REQUIRED, BE SURE TO USE REPLACEMENT PARTS SPECIFIED BY THE MANUFACTURER. Proper service and repair is important to the safe, reliable operation of all Hisense Electric Co., Ltd Equipment. The service procedures recommended by Hisense and described in this Service Guide are effective methods of performing service operations.

  • Page 4: Warning

    Hereafter throughout this manual, Hisense Electric Co., Ltd will be referred to as Hisense. 1.1 WARNING 1.1.1 Critical components having special safety characteristics are identified with a the Ref.
  • Page 5 (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the set by a wristband with resistance. Keep components and tools also at this same potential. 1.
  • Page 6 1.1.6 (1) Do not touch Signal and Power Connector while this product operates. Do not touch EMI ground part and Heat Sink of Film Filter. (2) Do not supply a voltage higher than that specified to this product. This may damage the product and may cause a fire.

  • Page 7: Notes

    (8) Do not damage or modify the power cable. It may cause fire or electric shock. (9) If the power cable is damaged, or if the connector is loose, do not use the product: otherwise, this can lead to fire or electric shock. (10) If the power connector or the connector of the power cable becomes dirty or dusty, wipe it with a dry cloth.
  • Page 8 specified. If any connection other than the one specified is made between the measuring equipment and the high voltage power supply block, it can result in electric shock or activation of the leakage-detection circuit breaker. • When installing the LCD module in, and removing it from the packing carton, be sure to have at least two persons perform the work.
  • Page 9 These wires are fixed in position with the wire clamps so that the wires do not move, thereby ensuring that they are not damaged and their materials do not deteriorate over long periods of time. Therefore, route the cables and fix the cables to the original position and states using the wire clamps.

  • Page 10: Factory/Service Osd Menu And Adjustment

    2. Factory/Service OSD Menu and Adjustment 2.1 To enter the Factory OSD Menu a. With factory RC (remote control) 1. Press “M” button and enter factory mode. 2. Press “Menu” button and enter factory OSD menu. 3 . Press “CH+”/“CH-” button select the function menu, press “VOL+”/“VOL-” enter the selected function menu.
  • Page 11 B CUT COUNTRY R DRV OPTIONS G DRV FACTORY INIT B DRV TEST PATTERN VERSION NON STANDARD LOGO ADC ADJUST NULL HISENSE Only in component and VGA WELCOME SOURCE ,The “ ” ADC Adjust Can be chosen. - 11 -...
  • Page 12 OPTION FACTORY INIT SOURCE QINGDAO TOFAC HUANGDAO HUNGARY STARTUP MENU 1 FRANCE Search Sensitive 1 AUSTRALIA RF NTSC CLEAR PROTECTLY HDCP OUT OR IN 1 CLEAR UNPROTECTLY TEST PATTERN VERSION TEST PATTERN NUL VERSION PANEL TYPE FLASH 2.2.2、Design Menu - 12 -...
  • Page 13 DESIGN MENU PICTURE MODE SOUND MODE PICTURE CURVE AUDIO CURVE SSC SETTING SAVING MODE PICTURE MODE SOUND MODE MODE STANDARD MODE USER BRIGHTNESS 120HZ CONTRAST 500HZ COLOUR 1.5KHZ 5KHZ 10KHZ PICTURE CURVE AUDIO CURVE MODE BRIGHTNESS MODE VOLUME CURVE 0 CURVE 0 CURVE 25 CURVE 25...
  • Page 14 SSC SETTING SAVING MODE DDR SSC DDR MCM LVDS SSC LVDS PCM Note ： The above “Factory/Service OSD Menu” are reference only, please refer to the actual units to determine the appearances. - 14 -...

  • Page 15: Software Upgrading

    3. Software Upgrading Before upgrading, read the following. 1、Before upgrading，Write down the ADC Calibration values of the channel of VGA and component。 2、Upgrade the software. 3、To clear the EEPROM . A Select the item “Clear Unprotected”. B Press VOL+ button to clear the EEPROM data. C Close the OSD menu after 5 seconds.
  • Page 16 Choose “system”option from the “control panel” Click the “system” icon as the following Choose the “hardware” option from the dialog window - 16 -...
  • Page 17 Click“device management” icon as the following Choose the port (COM and LPT1) - 17 -...
  • Page 18 Choose the ECP print port (LPT1） Click the port of print （LPT1）as the following - 18 -...
  • Page 19 Choose “port setting”option as the following - 19 -...
  • Page 20 Find the folder where the ISP_TOOL4.0.9 lies in. 2、 There are three folders/files in this folder together. DLPORTIO.dll and FTD2XX.DLL must be in the same folder Double click the ISP_TOOL4.0.9 icon, and then a dialog window will show as below. - 20 -...
  • Page 21 Click the Config button. And then a dialog window will show as below. Port Type setting is LPT1 Base Addr setting is 0x378 Draw on the front of “pin 1 switch UART/I2c” Speed setting is 99 As following Choose“SDA in”and setting “PIN” is “PIN10”。 Notes: Do not draw on the front of “Reverse High”。...
  • Page 22 Choose “SCL in”and setting “PIN” is “PIN11”。 Notes: Do not draw on the front of “Reverse High”。 As following Choose “SDA out”and setting “PIN” is “PIN4” Notes: Draw on the front of “Reverse High”。 As following。 Choose “SCL out”and setting “PIN” is “PIN2” Notes: Draw on the front of “Reverse High”...
  • Page 23 After having finished all above, clicking the “Apply ”button to complete the configuration。 3.1.2 Hardware connecting You can update the software through a special tool (as following) Connect the Debug board to the TV use VGA interface, the other parallel port to the - 23 -...
  • Page 24 computer, just as the following。 - 24 -...

  • Page 25: Upgrading With The Isp_Tool4.0.9

    3.2 Upgrading with the ISP_TOOL4.0.9 3.2.1 Double click the ISP_TOOL4.0.9 icon and a dialog window will show as following。 Click the“Read ”button。 - 25 -...
  • Page 26 Choose the update file from the folder。 - 26 -...
  • Page 27 The update file has been chosen successfully。 Click the“Auto”button and choose parameters as following。 Click the“Run”button Click the“connect”button,then show a dialog box as following。 - 27 -...
  • Page 28 If show above then click the“Run”button again and again，till show the following dialog window。 - 28 -...

  • Page 29: Usb Software Upgrading

    The above appears on the screen-the word “program ok”shows in the information displaying window,indicating upgrading is over。 3.2.2 After the update is over. Must Confirm the software Version in the Version Menu. If the update is successful, enter Factory Init Menu and select “Clear Unprotectly” a.
  • Page 30 3.3.2    the “Function” Menu “Software Update” choose “on” ， see the next figure。       3.3.3 AC power off, then restart the TV.        - 30 -...
  • Page 31         - 31 -...
  • Page 32   3.3.4 After update success, AC power off, and restart the TV.  If only appear the figure: “ Binary file detecting” ， the last three figures not. Please modify the  name of sotrware.  3.3.5、 After the update is over. Must confirm the software Version in the Version Menu. If the update is successful, enter Factory Init Menu and select “Clear Unprotectly” d. Press VOL+ button to clear the EEPROM data. e.
  • Page 33   3.3.6、Chasis MST6E16 includes 6E16GS and 6E16JS Chassis 6E16GS must be the last 8 bit figures and letters in front ot .bin For example : LCD19W58AM(30) named D19W58AM.bin. Chassis 6E16JS must be the TV name in front of.bin. For example : LCD19W58AM(30) named LCD19W58AM.bin.

  • Page 34: Circuit Instruction

    4. Circuit instruction 4.1 Main board Power assign and block diagram Power assign: The Powerd only has 12V output ，other voltages are converted from 12V. a. 5Vstb is converted by U10 from 12V，5VAIN and +5V_USB are converted by U7 from 5Vstb. b.

  • Page 35: Image And Signal Process

    4.2 Image and signal process e. RF Signal RF Signal pass Tuner(U22) and surface acoustic wave filter(U23、U25) then output SIF and VIF signal, which input to the main IC to have convert. AV Signal The video signal of AV input from terminal XS2，last enter the pin 37 of U41. as following The CVBS video signal of SCART input from terminal XS39, last enter the pin35 of U41.
  • Page 36 The YC video signal of S-Video input from terminal XS31, last enter pin 32、33 of U41. as following The RGB video signal of SCART input from terminal XS39, Ypbpr video signal of SCART input from terminal XS7. The two signals pass U30 (IC\P15V330Q), then enter pin17-20 of U41. last pass XP11/J2 directly output to the Panel - 36 -...
  • Page 37 PC（VGA）signal input from Terminal XS39, after having converted,. last enter the pin 22、24、 25、26 of U41. Audio signal of HDMI and USB directly input IC U41. Output of Scart (owning to have CANAL+ function , only output RF Signal)which by Pin 40 of U41, As the following amplified circuit..
  • Page 38 Audio XS7 （YPbPr and VGA mutual the channel） Audio XS2 （AV and SV mutual the channel） 2. Control Process： The Power only has 12V output ，other voltages are converted from 12V. U4 and U7 can interrupt other voltages while standby, only reserve standby 5V. as following. When TV Power on , Standby Signal is High level, 5VAIN Power suppluy normally ;...
  • Page 39 The video input signal of SCART RGB and Component was converted by U30, controlled by AU-SW0 signal. According current signal choose one channel output from 4、7、9 of U30 The control method as following: Current channel AU-SW0 Switch output signal Component Low level Component YPbPr SCART...
  • Page 40 SCART High level SCART RGB The main control signal, as list: Internet mark Control Signal recommend Remark STANDBY PW_CTL pass V1、V26 Standby signal（Power High level power on inverse phase control） PW_CTL High level power on BL-ON/OFF ON_PBACK pass V2 High level power on BL-control inverse phase ON_PBACK...

  • Page 41: The Main Ic Description

    Key “1” Key1-in Remote control signal IR-SYNC 4.3 The main IC description 74HC4052D： - 41 -...
  • Page 42 - 42 -...
  • Page 43 AOZ1021 - 43 -...
  • Page 44 RF7314 - 44 -...
  • Page 45 - 45 -...
  • Page 46 MP1482 - 46 -...
  • Page 47 TPA1517 - 47 -...
  • Page 48 - 48 -...

  • Page 49: Troubleshooting

    4.4 Troubleshooting 4.4.1 Troubleshooting for Remote Control Remote control does not work Try new batteries Replace battery Replace RC Replace remote control Check IR receiver Change Led & IR board Replace Led & IR BD Change Led & IR cable Replace Led &...

  • Page 50: Troubleshooting For Function Key

    4.4.2 Troubleshooting for Function Key Buttons does not work Check solder connections and Check switches see if any switches are stuck. Replace Key BD Check key board Check Key BD cable Change Key BD Replace main board - 50 -...

  • Page 51: Tv Won't Power On

    BD or Keypad one works Try Power on by RC and Button Check signal Panel Bright Source Neither Both works Work Replace Main Replace Main BD Power on Replace Panel (to contact Hisense tech support.) Replace Power BD - 51 -...

  • Page 52: Troubleshooting For Audio

    4.4.4 Troubleshooting for Audio No sound Reconnect Check connecter Replace speaker wire Check speaker wire Replace speaker set Check speaker set Replace main board Power Supply Board - 52 -...

  • Page 53: Troubleshooting For Tv/Vga/Hdmi Input

    4.4.5 Troubleshooting for TV/VGA/HDMI input No picture on the screen Check Signal Source Make sure signal source is available Reconnect Check connect Replace cable Check cable Replace main board - 53 -...

  • Page 54: Troubleshooting For Ypbpr Input

    4.4.6 Troubleshooting for YPbPr input No picture on the screen Check Source work or not Check Source Device Reconnect Check connect Check Wires (Green Blue, Red) Replace wires Replace main board - 54 -...

  • Page 55: Troubleshooting For Video/S-Video Input

    4.4.7 Troubleshooting for Video/S-Video input No picture on the screen Check Source work or not Check Signal Source Reconnect Check connect Replace Cable/Wires Check Cable/ Wires Replace main board - 55 -...

  • Page 56: Schematic Circuit Diagram

    5. Schematic circuit diagram - 56 -...
  • Page 57 VD812 VD812 power board circuit RT801 RT801 F801 F801 C810 C810 C856 C856 T801 T801 R806 R806 VD801 VD801 VD802 VD802 L803 L803 W812 W812 W818 W818 2245 R817 R817 FUSE-HX FUSE-HX C802 C802 C803 C803 R801 R801 R804 R804 C812 C812 CAP-HX...
  • Page 58 main board pcb 1861 5Vstb TO Inverter Board +12V_IN HIGH NORMAL 5Vstb XP26 XP26 LOW STANDBY 4.7K/NC 4.7K/NC 5Vstb BL-ON/OFF STANDBY NC/0 NC/0 PW_CTL STANDBY 5VAIN BL-ADJUST BL-ADJUST L65 FB L65 FB R203 R203 4.7K 4.7K 10K/NC 10K/NC C148 C148 4.7K 4.7K HIGH NORMAL...
  • Page 59 1861 1084-3.3 1084-3.3 MST6E16GS L48=FB,U6=NC NC/AMS1117-3.3 NC/AMS1117-3.3 MST6E16JS L48=NC,U6=1117 AMS1117-ADJ AMS1117-ADJ 2.6V for MST6E16 and DDRAM +3.3AVDD +3.3Vstb +3.3Vstb NC/FB NC/FB 5Vstb 5VAIN C360 C360 C388 C388 C385 C385 C386 C386 +2.6VM 22uF 22uF 0.1uF 0.1uF 22uF 22uF 0.1uF...
  • Page 60 R682 R682 NC/0 NC/0 PWMB 0.1uF 0.1uF 0.1uF 0.1uF PWMB RP19 100 RP19 100 ：采用 ； ：采用 ； MST6E16GS R296 MST6E16JS R350 MST6E16GS 采用 R418 、 R683 R427 R427 Not 5V-tolerant PWMB：如果确实需要，优先选择PWM0，便于频率调整； 采用 、 10K/NC 10K/NC MST6E16JS R680 R427 +3.3Vstb +3.3Vstb...
  • Page 61 main board pcb 1861 XS32 XS32 HDMI_1 HDMI_1 HDMI2-RX2+ INPAQ_VPORT INPAQ_VPORT DATA2+ DATA2 SHIELD HDMI2-RX2- INPAQ_VPORT INPAQ_VPORT DATA2- HDMI2-RX1+ INPAQ_VPORT INPAQ_VPORT 24C02=>EDID code must DATA1+ GND1 DATA1 SHIELD be upto 256byte space, HDMI2-RX1- VD10 VD10 INPAQ_VPORT INPAQ_VPORT DAT1A- GND2 HDMI2-RX0+ VD11 VD11 INPAQ_VPORT...
  • Page 62 main board pcb 1861 VGA/5V XS36 XS36 R113 R113 RXD0 RXD0 YPbPr R111 R111 TXD0 TXD0 VGA-Bin BIN+ PC_L R213 R213 PC-Lin BIN+ PC-Lin VGA-Gin GIN+ GIN+ VGA-Rin RIN+ PC_R R210 R210 PC-Rin RIN+ PC-Rin VD63 VD63 VD64 VD64 VD58 VD58 VD59 VD59...
  • Page 63 main board pcb 1861 5VAIN_4052 5VAIN AV2 Input R289 0/10K R289 0/10K L18 FB/10K L18 FB/10K AV2-IN R186 R186 AV2-Vin+ AV2-Vin+ XS1B XS1B AV_IN AV_IN R288 R288 C339 C339 C344 C344 C348 C348 左 左 下 下 R187 R187 NC/10K NC/10K 10uF 10uF...
  • Page 64 main board pcb 1861 5V-IF R233 R233 R234 R234 5V and 12V for Tuner +12V R236 R236 R237 R237 R238 R238 R258 R258 R331 R331 C300 C300 C219 C219 R317 R317 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 4.7K 2.2uF 2.2uF...
  • Page 65 main board pcb 1861 TPA1517(可兼容TDA1517P,10、11NC即可) +12V 6VBuf1 CA84 100uF/16V CA84 100uF/16V R437 R437 CA24 CA24 R415 R415 R414 R414 OP_VCC1 100uF/16V 100uF/16V PH-Lin R282 R282 C341 C341 CA83 CA83 0.1uF 0.1uF 100uF/16V 100uF/16V AMP-L R275 R275 C189 2.2uF C189 2.2uF AMP-L SGND SVRR...
  • Page 66 main board pcb 1861 Version A:在LCD22W57DEU_ZB_1701_C的基础上更改。 Page1 1、STANDBY部分待机低功耗IC电路，注意采用原芯片增加R37、R38 0R； 2、BL_ON/OFF、BL_ADJUST上拉电压预留； 3、USB滤波电容位置预留； Page2 1、DCDC部分待机低功耗IC电路，L8物料更换（成本），注意采用原芯片增加L16、更换L8； 2、VDDP、VDDP_PM调整，注意涉及电容排布，建议丝印依照原理图； Page3 1、LED、PWMB、HDMI_CEC等网络调整，注意采用原芯片增加R683； 2、ON_USB1、ON_PANEL上拉增加； 3、PW_CTL调整，注意IC差异； 4、部分GPIO上拉电压更改，参照紫红标注部分； Page6 1、4052 VCC电路优化，兼容原板增加R289 0R； 2、CVBSout VCC滤波电容，增加C346、C347； Page4-6 压敏电阻封装更改为0402，注意兼容原板定额更改； Page7 增加R352、R353，注意兼容原板定额更改。 Version B:在MST6E16JS_ZB_1861_A的基础上更改。 Page1 1、CA6位置调整，避免部分屏掉电残影等问题； Page2 1、删除L19、L21；//改板方便，不再更改； Page3 1、删除R456、R480；//改板方便，不再更改； 2、调整LED网络，删除R684,增加R427； 3、PCB增加主芯片散热焊盘； Page6 1、增加C194；...

Table of Contents