Download
Share
Print this page
  1. Manuals
  2. Brands
  3. UNAVi Manuals
  4. Car Navigation system
  5. ENB-X2
  6. Installation manual

UNAVi ENB-X2 Installation Manual

Kia sorento in-dash navigation
Hide thumbs Also See for ENB-X2:

Advertisement

Quick Links

Download this manual See also: Installation Manual
Kia Sorento In-Dash Navigation
MODEL: Kia Sorento 2011-2013
Information & Manual
.
CLASSFICATION
Installation Manual
Kia Sorento In-Dash Navigation DIY Installation Guide
DIY Installation Guide
[UVO Infotainment System Use Only]
(Professional Use)
WWW.BUYUNAVI.COM
Copyright © 2013 UNAVI USA, Inc. All rights reserved.
.
MODEL
ENB-X2
.
DOCUMENT NO
BU No. 20
.
.
VERSION
PAGE
1
1.1
Date: 5/6/2013

Advertisement

loading
Need help?

Need help?

Do you have a question about the ENB-X2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for UNAVi ENB-X2

Summary of Contents for UNAVi ENB-X2

  • Page 1 Kia Sorento In-Dash Navigation DIY Installation Guide Kia Sorento In-Dash Navigation DIY Installation Guide [UVO Infotainment System Use Only] MODEL: Kia Sorento 2011-2013 (Professional Use) WWW.BUYUNAVI.COM Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.

  • Page 2: Main Components

    MAIN COMPONENTS (Not actual size, Items shown may vary) Rear View Sorento fascia kit: - Fascia - Control keypad w/cable - Main LCD Panel w/Mounting Bracket Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 3 Control box + SD Card Trip interface board External speaker GPS antenna + Magnetic plate Control box interface cable SMART cable SMART cable XM antenna adapter Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.

  • Page 4: Tools Required

    Electrical Connectors & Tools - (Wire stripper, Crimper, T-Tap, etc.)  Hand Saw/Reciprocating Saw *  Heat Gun Required Tools Pre-installation picture of non-navigation equipped models (Trim levels may vary) Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.

  • Page 5: Gps Antenna Installation

    Once the antenna has been positioned, route the antenna cable carefully to avoid damage. Position the GPS antenna in the center of the vehicle at the highest point with a clear view of the sky. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 6 Put the gear shifter in N (neutral) position and carefully pull up the shift knob. Remove the floor console upper cover and disconnect the plug underneath it. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 7 (Apply protective tapes and take care not to damage and scratch the interior dash and its related parts) Remove the seat warmer switch module and rest of the connectors. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 8 Kia Sorento In-Dash Navigation DIY Installation Guide Remove the screws (2EA) marked in white circles. Gently pull off the center fascia panel and disconnect the plug behind the factory clock display. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 9 Kia Sorento In-Dash Navigation DIY Installation Guide After removing the screws, remove the heater control module. (Images shown on this page may vary) Remove the audio assembly after loosening the mounting screws. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 10 Disconnect the ribbon cable (FCC) from Gently pull the locking tab away from the the back of the audio faceplate ONLY. faceplate to release the ribbon cable. **Use Caution** Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 11 Loosen the screws (4EA) from the audio head unit top cover Remove the top cover after loosening the screws. Remove the two screws as marked in black arrows shown above. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 12 [WARNING] This TRIP MODULE is designed for specific models. Improper use such as failure to follow instructions and use with incompatible radio will damage this module and the radio unit! Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 13 Kia Sorento In-Dash Navigation DIY Installation Guide  When attaching the ribbon cable on all UVO systems, for those familiar with Unavi installs, note that it is wider and uses a different type of connector than the standard radio units.
  • Page 14 (Use screws provided in the kit to mount the Trip Interface board). Front view of the Trip Interface board mounted on to the front replacement bracket. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 15 CD-ROM drive as shown. Front view of the front replacement bracket with Trip Interface board assembled. Make sure the top cover is screwed back on to the radio unit. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 16 Kia Sorento In-Dash Navigation DIY Installation Guide Screw on the replacement mounting brackets (Left and Right) as shown. Open the glove box and turn the side tabs to disconnect it. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 17 (To completely remove the glove box, pull out the two pins in the back) Route the Control box interface cable around from behind the glove box and out through the center dash panel opening. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 18 Use Unibit to drill a hole on the back of the glove box (about 3/4-inch) just wide enough for the SD/USB interface cables to slide through.**Proceed with Caution** Mount the control box inside the glove box using a double-sided tape or Velcro. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 19 Kia Sorento In-Dash Navigation DIY Installation Guide Saw off the plastic trims in the center dash along the white lines. Image of the dash trim pieces removed. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 20 Bend the audio support bracket downwards. To allow more space for the audio unit behind the dash, cut off the metal piece on the chassis frame as shown. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 21 Make sure the GPS receiver is mounted (rounded side up facing the sky) to a non-metallic panel or on the front windshield glass. Route the antenna cable carefully to avoid damage. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 22 Kia Sorento In-Dash Navigation DIY Installation Guide Connect the external speaker to the female connector labeled “BUILT-IN SPEAKER” This speaker will allow sound output from the UNAVI system when the audio is in XM/Radio/CD/MP3/Bluetooth mode. Sound output from the system will use the factory speakers under “AUX” mode only.
  • Page 23 Plug in the XM antenna adapter to the XM port on the back of the audio unit. Connect the factory XM antenna cable to the other end of the XM antenna adapter. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 24 Choose a clean section of metal or the vehicle chassis when attaching the ground connection. Be sure to clean the area of any dirt or grease. Connect the main factory audio cable (24-pin) to the SMART cable harness Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 25 Clear of any obstructing cables and mount the audio unit back into the dash panel. Check the cables are not being too tightly squeezed in the back of the audio unit. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 26 Kia Sorento In-Dash Navigation DIY Installation Guide Plug in the 20-pin connector to the Trip Interface board as shown. Disassemble the components from the center fascia panel as shown. Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 27 Installation Manual VERSION PAGE Kia Sorento In-Dash Navigation DIY Installation Guide Assemble the factory clock display onto Unavi fascia kit as shown. Plug in the 10-pin keypad cable to the Trip Interface board as shown. Information & Manual Date: 5/6/2013...
  • Page 28 Plug in the remaining cables to the back of the LCD panel as shown. [INSTALLATION COMPLETE] For additional support and information, please visit us at www.buyunavi.com Thank you for choosing UNAVI! Information & Manual Date: 5/6/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.