Download
Share
Print this page
  1. Manuals
  2. Brands
  3. UNAVi Manuals
  4. Car Navigation system
  5. Kia Optima 2011+
  6. Installation manual

UNAVi Kia Optima 2011+ Installation Manual

In-dash
Hide thumbs

Advertisement

Quick Links

Download this manual
.
.
.
CLASSFICATION
MODEL
DOCUMENT NO
ENB-X2
BU No. 8
Installation Manual
.
.
VERSION
PAGE
Kia Optima In-Dash Navigation DIY Installation Guide
1.4
1
Kia Optima In-Dash Navigation
DIY Installation Guide
[Standard Radio Use Only]
MODEL: Kia Optima 2011+
(Professional Use)
WWW.BUYUNAVI.COM
Information & Manual
Date: 1/30/2013
Copyright © 2013 UNAVI USA, Inc. All rights reserved.

Advertisement

loading
Need help?

Need help?

Do you have a question about the Kia Optima 2011+ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for UNAVi Kia Optima 2011+

Summary of Contents for UNAVi Kia Optima 2011+

  • Page 1 PAGE Kia Optima In-Dash Navigation DIY Installation Guide Kia Optima In-Dash Navigation DIY Installation Guide [Standard Radio Use Only] MODEL: Kia Optima 2011+ (Professional Use) WWW.BUYUNAVI.COM Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.

  • Page 2: Main Components

    (Not actual size, Items shown may vary) Rear View Optima fascia kit: - Fascia - Bluetooth Antenna Port - Touch Sensor PCB - Main LCD Panel w/Mounting Bracket Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 3 Mounting brackets (Top & Bottom) Trip interface board Control box + SD Card External speaker GPS antenna + Magnetic plate SD + USB interface cables SMART cable Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.

  • Page 4: Tools Required

    Power Drill  Unibit*  Electrical Connectors & Tools - (Wire stripper, Crimper, T-Tap, etc.) Required Tools Pre-installation picture of non-navigation equipped models (Trim levels may vary) Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.

  • Page 5: Gps Antenna Installation

    Once the antenna has been positioned, route the antenna cable carefully to avoid damage. Position the GPS antenna in the center of the vehicle at the highest point with a clear view of the sky. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 6 (Apply protective tapes and take care not to damage and scratch the interior dash and its related parts) Remove the screws (2EA) once the panel cover is removed. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 7 Kia Optima In-Dash Navigation DIY Installation Guide Remove the screws (2EA) located on the bottom of the driver side panel assembly. Gently pull off the panel assembly as shown. (See next picture) Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 8 Carefully disconnect all connectors from the back of the panel. (Picture shown may vary based on vehicle trim levels) Image of driver side panel assembly removed. (Installation is the reverse of removal) Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 9 Use a panel remover to pull out the garnish surrounding the center fascia. Start from the top right-hand corner as shown and gently pull up. Image of center garnish removed. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 10 Remove the screws (4EA) to pull out the climate control assembly. Disconnect all connectors from the back. Remove the screw on top of the driver side right air vent. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 11 Pull out the driver side air vent panel as shown. Remove the mounting screws (6EA) to marked in white circles. Gently pull out the center fascia panel as shown. (Installation is the reverse of removal) Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 12 PAGE Kia Optima In-Dash Navigation DIY Installation Guide Carefully remove the air vent and white clips from the factory fascia panel… …and relocate it to the UNAVI fascia kit as shown. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 13 As the audio assembly is being pulled out, carefully disconnect all cables behind the unit. Rear view of the audio head unit after removing connectors and cables. If applicable, remove the rear frame stabilizer. (Picture shown may vary) Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 14 Gently pull back the sleeve of the Disconnect the ribbon cable (FCC) from Bluetooth antenna cable to disconnect it. the back of the audio faceplate ONLY. **Use Caution** Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 15 Remove the top cover after loosening the screws as shown. Remove the screws hidden underneath Remove the screws securing the front bracket. the two openings marked above. (These screws will be reused) Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 16 Slide in the ribbon connector through the bottom opening of the front replacement bracket. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 17 NEVER attempt to connect the ribbon cable to the Trip Interface Board like the picture shown above as it may cause permanent damage to the audio unit! Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 18 - Push the lock down to secure the cable *Please check after installation when the radio unit is powered on* Red LED lights on the circuit board will flash intermittently indicating data communication. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 19 Screw under the two openings as shown using the screws removed from an earlier step and install the top cover back on. Screw on the replacement mounting brackets (Top and Bottom). Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 20 Kia Optima In-Dash Navigation DIY Installation Guide Open the glove box and turn the dampers to disconnect it. Disconnect the glove box lift to completely release the compartment. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 21 If necessary, use Unibit to drill a hole on the back of the glove box (about 3/4-inch) just wide enough for the SD/USB interface cables to slide through.**Proceed with Caution** Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 22 EXAMPLE ONLY Run the interface cables through the drilled hole. Mount the control box inside the glove box as shown. Bend the audio support bracket downwards. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 23 Make sure the GPS receiver is mounted (rounded side up facing the sky) to a non-metallic panel or on front windshield glass. Route the antenna cable carefully to avoid damage. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 24 Kia Optima In-Dash Navigation DIY Installation Guide Connect the external speaker to the female connector labeled “BUILT-IN SPEAKER”. This speaker will allow sound output from the UNAVI system when the audio is in XM/Radio/CD/MP3/Bluetooth mode. Sound output from the system will use the factory speakers under “AUX” mode only.
  • Page 25 Kia Optima In-Dash Navigation DIY Installation Guide Connect the main factory audio cable (24-pin) to the SMART cable harness Reconnect the remaining audio unit connectors and cable as shown. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 26 Plug in the 6-pin “TRIP POWER” connector to the Trip Interface board as shown. Plug in the 5-pin “TRIP PCB” connector to the Trip Interface board as shown. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 27 (Images shown on this page may vary) Gently pull back the Bluetooth antenna cable sleeve and connect to the Bluetooth antenna port located behind the fascia panel as shown. Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 28 Plug in the remaining cables to the back of the LCD panel as shown. [INSTALLATION COMPLETE] For additional support and information, please visit us at www.buyunavi.com Thank you for choosing UNAVI! Information & Manual Date: 1/30/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.