Download
Share
Print this page
  1. Manuals
  2. Brands
  3. UNAVi Manuals
  4. Car Navigation system
  5. ENB-X2
  6. Installation manual

UNAVi ENB-X2 Installation Manual

Genesis coupe in-dash navigation hyundai genesis coupe 2010-2012
Hide thumbs Also See for ENB-X2:

Advertisement

Quick Links

Download this manual See also: Installation Manual
.
.
.
CLASSFICATION
MODEL
DOCUMENT NO
ENB-X2
BU No. 4
Installation Manual
.
.
VERSION
PAGE
Genesis Coupe In-Dash Navigation DIY Installation Guide
1.3
1
Genesis Coupe In-Dash Navigation
DIY Installation Guide
MODEL: Hyundai Genesis Coupe 2010-2012
(Professional Use)
WWW.BUYUNAVI.COM
Information & Manual
Date: 1/31/2013
Copyright © 2013 UNAVI USA, Inc. All rights reserved.

Advertisement

loading
Need help?

Need help?

Do you have a question about the ENB-X2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for UNAVi ENB-X2

Summary of Contents for UNAVi ENB-X2

  • Page 1 Installation Manual VERSION PAGE Genesis Coupe In-Dash Navigation DIY Installation Guide Genesis Coupe In-Dash Navigation DIY Installation Guide MODEL: Hyundai Genesis Coupe 2010-2012 (Professional Use) WWW.BUYUNAVI.COM Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.

  • Page 2: Main Components

    MAIN COMPONENTS (Not actual size, Items shown may vary) LCD – Front LCD – Rear Genesis Coupe fascia kit: - Fascia - Main LCD Panel w/Mounting Bracket Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 3 Audio (AUX) Cable CAN Cable Control box + SD Card Trip interface board External speaker GPS antenna + Magnetic plate SD + USB interface cables Main cable Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.

  • Page 4: Tools Required

    Power Drill  Unibit*  Electrical Connectors & Tools - (Wire stripper, Crimper, T-Tap, etc.) Required Tools Pre-installation picture of non-navigation equipped models (Trim levels may vary) Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.

  • Page 5: Gps Antenna Installation

    Once the antenna has been positioned, route the antenna cable carefully to avoid damage. Position the GPS antenna in the center of the vehicle at the highest point with a clear view of the sky. Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 6 (Apply protective tapes and take care not to damage and scratch the interior dash and its related parts) Lift up the top plastic cover. (Picture shown may vary) Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 7 Cut the factory center cover along the white dotted lines. A reciprocating saw may be useful for this procedure. **Proceed with Caution** (See sample image below) Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 8 PAGE Genesis Coupe In-Dash Navigation DIY Installation Guide Remove the mounting clips (4EA) from the LCD monitor housing. Transfer these clips onto the pre-assembled UNAVI fascia kit. Unscrew the marked sections to remove the trip monitor. Information & Manual Date: 1/31/2013...
  • Page 9 PAGE Genesis Coupe In-Dash Navigation DIY Installation Guide Disconnect the connector behind the trip monitor. Cut off the two mounting tabs outlined in white dotted box. Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 10 Genesis Coupe In-Dash Navigation DIY Installation Guide Open the glove box and locate the two plastic stoppers. Pull apart the stoppers at a 45° angle on both sides. Removed stopper as shown. Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 11 Use Unibit to drill a hole on the back of the glove compartment (about 3/4-inch) just wide enough for the SD/USB interface cables to slide through. **Proceed with Caution** Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 12 Run the interface cables through the drilled hole and assemble the glove Mount the control box inside the glove box using a double-sided tape or Velcro. Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 13 (1) Connect the factory LCD monitor cable to the CAN cable. (2) Connect the 6-pin “TRIP PCB” connector to the Trip Interface board. (3) Connect the 3-pin “POWER” connectors (Red/Yellow/Black) to each other. Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 14 Plug in the 5-pin Trip cable to the Trip Interface board as shown. The Trip interface board must be mounted somewhere in the back of the center dash panel. Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 15 Genesis Coupe In-Dash Navigation DIY Installation Guide Connect the external speaker to the female connector labeled “SPEAKER”. This speaker will allow sound output from the UNAVI system when the audio is in XM/Radio/CD/MP3/Bluetooth mode. Sound output from the system will use the factory speakers under “AUX” mode only.
  • Page 16 Make sure the GPS receiver is mounted (rounded side up facing the sky) to a non-metallic panel or on the front windshield glass. Route the antenna cable carefully to avoid damage. Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 17 Connect the audio cable (Red/White RCA plugs) to the “AUX OUT” (Red/White RCA input) located on the main cable. Slide the audio cable in through the main crash pad. Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 18 (Images shown on this page may vary) Slip in the audio cable behind the side panel cover and lead it all the way across to the center console. Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 19 Lift up the console box to bring out the audio cable through the bottom opening. Screw the two bolts back in to tighten the console box to its place. Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.
  • Page 20 Genesis Coupe In-Dash Navigation DIY Installation Guide Plug in the audio cable jack into the AUX input of the factory multimedia jack. (Picture shown may vary) Sound output from the UNAVI system will utilize the factory speakers under AUX mode. Main Cable SD/USB Interface Cable Connect the remaining cables to the back of the main LCD unit as shown.
  • Page 21 VERSION PAGE Genesis Coupe In-Dash Navigation DIY Installation Guide [INSTALLATION COMPLETE] For additional support and information, please visit us at www.buyunavi.com Thank you for choosing UNAVI! Information & Manual Date: 1/31/2013 Copyright © 2013 UNAVI USA, Inc. All rights reserved.