Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Max-Thrust Manuals
  4. Toy
  5. Douglas A1 Skyraider
  6. Assembly and instruction manual

Max-Thrust Douglas A1 Skyraider Assembly And Instruction Manual

Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
Douglas A1 Skyraider
Sport Scale Model Aircraft
Assembly and Instruction Manual
Warning:
This radio controlled model is not a toy. It requires skill to fly and is not recommended for
the novice pilot. It should not be operated by children without the supervision of a suitably
experienced adult. Max-Thrust reserves the right to modify the specification of this model at
any time.
© Century UK Limited 2011. All rights reserved.

Advertisement

loading

Related Manuals for Max-Thrust Douglas A1 Skyraider

Summary of Contents for Max-Thrust Douglas A1 Skyraider

  • Page 1 This radio controlled model is not a toy. It requires skill to fly and is not recommended for the novice pilot. It should not be operated by children without the supervision of a suitably experienced adult. Max-Thrust reserves the right to modify the specification of this model at any time.
  • Page 2 Failure to do so could result in a loss of control and possibly a crash. Overview Thank-you for purchasing this MAX-THRUST Douglas A1 Skyraider radio controlled model aircraft. The A1 Skyraider offers a stunning combination of terrific looks and sensational flight performance.
  • Page 3 Parts List. 1. Fuselage 9. Drop Tank 2. Wing Panels 10. Bombs 3. Horizontal Stabilizer 11. Retracts and Doors 4. Fin & Rudder 12. Fixings Pack 5. Aerial 13. Propeller 6. Wing Guns 14. Propeller Adaptor 7. Canopy 15. “Y” Leads 8.
  • Page 4 Tools required to complete 1. Screwdrivers 4. Scissors 2. Pliers 5. Measure or Ruler 3. Modelling Knife Additional items required to complete 3350mAh - 5550mAh 4S 14.8V Li-Po battery (POWER-TECH 5550mAh 33C 4S 14.8V recommended Part No. PT-B-3355504S) Charger (Power-Tech C6, B606 or X-Drive 6 recommended) 2.4GHz Transmitter 2.4GHz Receiver Self-Adhesive Tape...
  • Page 5 1. Hinge check Check that all control surface hinges are firmly secured. If required they can be glued in position using a small quantity of the supplied adhesive. 2. Horizontal Tail Plane Fix the elevator control horn in the moulded recess as shown using two M2 x 15mm screws, (image 1).
  • Page 6 Apply adhesive sparingly to the mating surface of the horizontal tail plane and push the fin assembly into position. Remove any excess adhesive immediately. Secure in place using the two M3 x 40mm screws via the fixing holes positioned underneath the fuselage, (image 7). 4.
  • Page 7 Starting with the left hand wing panel, fix the aileron control horn and its backing plate in position using the four M2 x 15mm screws. The flap control horn is secured in position using four M2 x 25 mm screws. Check the operation of the wing servos and ensure they are correctly centred.
  • Page 8 Position the wing onto the fuselage and fix in place with the two M3 x 50mm screws, (image 15). Make certain that all control wires are kept inside the fuselage and do not foul the wing seat area. Connect aileron (marked CH1) and flap (marked CH6) control leads to the corresponding “Y”...
  • Page 9 If you wish to install a pilot figure, do so now. We recommend that you drill two small holes as shown in the clear canopy to allow any heat to disperse, (image 18). The canopy cover may require some trimming to obtain a perfect fit. This should be tested and trimmed if necessary before the canopy is assembled.