3/4" Overlay Panel Dimensions - Standard - GE ZISS480DRHSS Installation Instructions Manual

Design Guide
3/4" OVERLAY PANEL DIMENSIONS
(Standard Installation Only)
For a more custom appearance, overlay panels may
be installed on trimmed models, The overlay panel must
be secured to a 1/4" thick backer panel which slides
into the trim, A spacer panel 0,10" thick must be placed
between the overlay and backer panel,
Assemble the panels with glue and screws:
, Center the spacer panel on the backer panel, left to
right and top to bottom, Secure the panels with glue,
, Center the spacer and backer panel on the overlay
panel and secure with glue and screws, Screws must
be countersunk into the backer panel,
Door
L
Backer .
Panel ....................... Spacer
OverlaL
£ackerPanel
NOTE: Left-to-right offset is
not cllwc_y,s equcfl to top-to-
bottom of Fset,
,250" + ,70" + ,750" 7,7OO"Tote_/ P nnel Thickness
IMPORTANT NOTE - DISPENSER MODELS
The refrigerator is supplied with two dispenser trims,
one for framed panels and one for overlay panels, The
overlay dispenser trim is designed to fit a total panel
thickness of 1,100",
, If the panel is less than 1,100" a noticeable gap may
be created around the dispenser trim,
, If the panel is more than 1,100" the dispenser trim
cannot be secured to the door,
See Dispenser Trim Fit Example, page 12.
, The overlay panel must be constructed according to
the specifications shown to achieve the correct total
thickness,
, Alternative panel construction methods such as
securing a 3/4" panel to a 1/4" backer panel cannot
be used, Another method, routing a 3/4" thick panel
on all sides, cannot be used, These methods will not
result in the required 1,100" panel thickness,
A
Grille Panel B
F
Dispenser
Cutout
Freezer Fresh
Panel Food
Panel
-- m
_D_4 _E_
Dispenser Cutout
I_ 9-5/8" _1
15-3/8"
*Cut the dispenser apening after the backer, spacer and averlay
panels have been assembled,
IMPORTANT NOTE: Maximum tatal weight far the assembled
panels:
, Fresh faad daar panel - 75 Ibs,
, Freezer daar panel - 53 Ibs,
, Grille Panel- 18 Ibs,
36"Side-by-Side(in inches)
1/4" BackerPanel 33-7/8 9 68-3/8 14-9/16 18-9/16
,10"SpacerPanel 33 8-3/8 67 13-1/4 17-1/4
3/4" Overlay Panel 34-1/8 9-1/4 68-5/8 14-13/16 18-13/16
42" Side-by-Side (in inches)
1/4" Backer Panel 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16
,10" Spacer Panel 39 8-5/8 67 13-1/4 23-1/4
3/4" Overlay Panel 40-1/8 9-3/4 68-5/8 14-13/16 24-13/16
48" Side-by-Side (in inches)
1/4" Backer Panel 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16
,10" Spacer Panel 45 8-5/8 67 17-1/4 25-1/4
3/4" Overlay Panel 46-1/8 9-3/4 68-5/8 18-13/16 26-13/16