Page 1
Installation Instructions Side by Side Refrigerators ZIS360N,ZISB360D,ZISW360D ZISS360N,ZISS360D ZIS420N,ZISB420D,ZISW420D ZISS420N,ZISS420D ZIS480N,ZISB480D,ZISW480D ZISS480N,ZISS480D Design Guide With Installation Instructions Monogram:' We bring good things to life...
IMPORTANT staller. Product failure due to improper installation • Save these instructions not covered under the GE Appliance Warranty. local inspector's use. Observe all governing the Owner's Manual for warranty information. codes and ordinances. • Note to Installer-...
Design Guide THE INSTALLATION SPACE DIMENSIONS AND CLEARANCES 36" Models 12" 35",41",or4T' 42" Models 18" _,_aseWidth_,d 48" Models20" Shippingheight,The _*FinishedWidth_ refrigeratorcan be adjustedto fit into a cutout that is 83-1/2" rain,to 84-1/2"max, "83-1/2" Floorto height, Notethat the TopFrame 84 1/2"max top casetrim at the Rear 83 1/2"min...
Design Guide FramelessCabinets:The case trim overlaps cabinets at the to ) and sides. Therefore, frameless cabinets may require filler strips to prevent inter- Refrigerator ference with cabinet door swing. The 23-7/8"From Rearof opening must allow for filler strips. Refrigerator 1 " 2"...
Design Guide FramelessCabinets: The case trim overlaps cabinets at the top and sides. Refrigerator Therefore, frameless cabinets may require filler _Case strips to prevent inter- ference with cabinet door swing. The opening must allow for filler strips, 23-7/8" FromRearof Refri{erator ..
Design Guide 1/4" FRAMED PANEL DIMENSIONS 5/16" Trim Door Reveal If you choose to install framed panels, they must cut to the dimensions shown. The panels will slide into the frame on the door and grille. _1/4" Panel Non-Dispenser Models If the custom panel is less than...
Design Guide 3/4" OVERLAY PANEL DIMENSIONS Door For a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel must be secured to a 1/4" thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panel.
Design Guide DISPENSER MODELS: RAISED OVERLAY PANEL DESIGN 1/4"BackerPanel ,10" Spacer When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim. * The middle rail must be wide enough to allow for the dispenser trim to overlap the opening.
Design Guide SIDE PANELS FLOORING For proper installation, this refrigerator must be placed on a level surface of hard material that is at Side panels must be used whenever the sides of the the same height as the rest of the flooring. This surface should be strong enough to support a fully...
Installation Instructions • Remove four 7/16" [STEP 11 REMOVE PACKAGING bolts securing straps to the skid. CAUTION: Refrigerator ismuch heavier atthe CAUTION: DO top thanatthebottom - be careful w hen moving. NOT ATTEMPT TO When using a hand truck, handle from side only. ROLL UNIT OFF SKID.
Installation Instructions [STEP 41 INSTALL ANTI-TIP [STEP 2A] WATER LINE BRACKETS INSTALLATION WITH A REVERSE OSMOSIS SYSTEM WARNING: ANTI-TIP PRECAUTIONS The refrigerator is top-heavy must be secured Skip this step when not using an RO System prevent the possibility of tipping forward.
Installation Instructions _STEP 7] ADJUST DOOR SWING ISTEP 51 LEVEL REFRIGERATOR NOTE: This refrigerator has a 2-position door stop. All models have 4-point leveling. The front is sup- When space does not allow the door to swing open ported by leveling legs, the rear is supported fully to 130 °, you may change the door swing to a 90 °...
Installation Instructions ISTEP 81 INSTALL GRILLE PANEL To insert framed or overlay panel into the grille: * Raise the grille panel to stop position. Loosen Loosen Side Side Screw Screw AdjustNut Below Springto Accomodate PanelWeight * Loosen screws on side trim behind frame.
Installation Instructions [ STEP INSTALL FRAMED PANELS GotoStep for Overlay Panels Handle /Door_im [rim Refrigerator Door P - 4m Supplied Handle Shown in 114"Panel Position Install door panels: • Open door to 90 °. Remove the 6 Phillips head screws from the door handle.
Installation Instructions ISTEP 9AI INSTALL OVERLAY PANELS Door T rim Handle [rim Refrigerator Door Move Forward For3/4" Panel - - qml Supplied Handle Shown in Overlay Panel Position Install door panels: • Open door to 90 °. Remove the 6 Phillips head screws from...
Installation Instructions ISTEP 101 INSTALL DISPENSER [STEP 11] CONNECT WATER SUPPLY TRIM Check to be sure that refrigerator power cord is not Skip this step is you are installing a stainless plugged into the wall outlet. steel wrapped or a non-dispenser refrigerator. There are two dispenser trims shipped with your refrigerator.
Installation Instructions [STEP 14] INSTALL TOEKICK ISTEP 121 CONNECT POWER • Locate the supplied toekick (shipped taped to • Connect refrigerator power cord plug to a properly the side of the refrigerator). Install with 2 screws grounded receptacle, accessible through the top of provided, adjust to desired height and tighten screws.
Page 20
Note: While performing installations described in this book, safety glasses or goggles should be worn, For Monogram _ local service #1 your area, call 1-800-4441845. Note: Product improvement is a continuing endeavor Ceileral Electric. Therefore, materials, appearance specifications subject to change without notice.
Need help?
Do you have a question about the Monogram ZIS360N and is the answer not in the manual?
Questions and answers