3/4" Overlay Panel Dimensions - GE ZlS360N Design & Installation Manual

Design Guide
3/4" OVERLAY PANEL DIMENSIONS
For a more custom appearance, overlay panels may be
installed on trimmed models. The overlay panel i/ltlst
be secured to a 1/4" thick backer panel which slides
into the trim. A spacer panel 0.] 0" thick must be
placed between the overlay and backer panel.
Assemble the panels with glue and screws.
• Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
• (:enter the spacer and backer panel on the overlay
panel and secure with glue and screws. Screws must
be countersunk into the backer panel.
IMPORTANT
NOTE
- DISPENSER MODELS
The refiigerator is sui)plied with two dispenser trims,
one fl)r fl'amed panels and one fin" overlay panels.
The overlay dispenser trim is designed to fit a total
panel thickness of 1.100".
• If the panel is less than ] .100" a noticeable gap may
be created around the dispenser trim.
• If the panel is more than 1.100" the dispenser trim
cannot be secured to the door.
See Dispenser Trim Ht Example, page 9.
\
Door
t
1/4"
Backer_ .10"
Panel _Spacer
Overlay Panel
Backer Panel
NOTE: Left-to-right offset
is not always equal to
top-to-bottom offset.
.2BO"+ .10" + .750" = 1.1OO"Total P anel Thickness
• The overlay panel
must
be constructed according to
the specifications shown to achieve the correct total
thickness.
• Alternative panel const_ uction methods such as
secming a 3/4" panel to a 1/4" backer panel cannot
be used. Another method, routing a 3/4" thick
panel on all sides cannot be used. These methods
will not result in the required 1.100" panel thickness.
When a raised panel design is to be used, a custom
middle rail is required, See page 9 for details,
Grille Panel i
7
F
Dispenser j
Cutout
Freezer Fresh Food
Panel Panel
_D_] _E_
Dispenser Cutout
15-3/8"
I_ 94/8"
36" Side-by-Side (in inches)
*Cut the dispenser opening after the backer, spacer and overlay
panels have been assembled.
IMPORTANT NOTE: Maximum total weight for the assembled
panels:
• Fresh food door panel-75 Ibs.
• Freezer door panel -53 Ibs.
• Grille Panel - 18 Ibs.
1/4"Backer Panel 33-7/8 9 68-3/8
.10"SpacerPanel 33 8-3/8 67
3/4"Overlay Panel 34-1/8 9-1/4 68-5/8
42" Side-by-Side (in inches)
14-9/16 18-9/16
13-1/4 17-1/4
14-13/16 18-13/16
1/4"Backer Panel 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16
.10"SpacerPanel 39 8-5/8 67 13-1/4 23-1/4
3/4"Overlay Panel 40-1/8 9-3/4 68-5/8 14-13/16 24-13/16
48" Side-by-Side (in inches)
1/4"Backer Panel 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16
.10"SpacerPanel 45 8-5/8 67 17-1/4 25-1/4
3/4"Overlay Panel 46-1/8 9-3/4 68-5/8 18-13/16 26-13/16
8