Related Manuals for GE ZISS36D SS
Summary of Contents for GE ZISS36D SS
-
Page 1: Stainless Steel
® GE Monogram Installation Instructions Stainless Steel Built-In Refrigerators Models ZISS36D SS, ZISS36N SS ZISS42D SS, ZISS42N SS ZISS48D SS, ZISS48N SS... -
Page 2: Table Of Contents
Cet appareil doit être correctement mis à la terre. Consulter « Mise à terre du réfrigérateur », page 6. If you have a question concerning the installa- WARNING tion of this product, call the GE Answer ® Center Consumer Information Service at •... -
Page 3: Flush Or Semi-Flush Enclosure Installations
Design Information Stainless Steel Built-In Refrigerators Advance Planning Flush or Semi-Flush Enclosure Installations 0" 3/4" True Flush Installation Semi-Flush Installation In a flush installation, These refrigerators the refrigerator doors can also be installed will align evenly with the semi-flush into an enclosure front face of adjacent cabinet using the minimum cutout doors. -
Page 4: Installation Examples
Design Information Stainless Steel Built-In Refrigerators Side panels are required whenever the sides Therefore, the rough-in dimensions must of the refrigerator will be exposed. allow for side panel thickness. In both a flush and semi-flush installation, the finished 1/2" to 3/4" side panels are normally set into dimension, (the width of the opening after place and fastened to adjacent cabinetry or to side panels are installed), must accommodate... -
Page 5: Installation Preparation
Installation Preparation Stainless Steel Built-In Refrigerators Product Models ZISS36D, ZISS36N Models ZISS42D, ZISS42N Models ZISS48D, ZISS48N A – 36" outside trim width A – 48" outside trim width A – 42" outside trim width Dimensions B – 35" case width B –... -
Page 6: Grounding The Refrigerator
Installation Preparation Stainless Steel Built-In Refrigerators IMPORTANT - (Please read carefully) Grounding FOR PERSONAL SAFETY, THIS APPLI- ANCE MUST BE PROPERLY GROUNDED. Refrigerator The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong (ground- ing) wall receptacle to minimize the possibil- ity of electric shock hazard from this appli- ance. -
Page 7: Tools Required
Installation Preparation Stainless Steel Built-In Refrigerators • Appliance Hand Truck • Tinsnips to cut banding • Drill and appropriate bits Tools • Tubing cutter • Stepladder • 7/16" socket with 3" extension Required • 7/16" open-end wrench • Bucket for ratchet •... -
Page 8: Step 2: Install Water Line
WARNING ATTENTION Step When connecting a GE Reverse Lors du raccordement au réfrigérateur Osmosis Water System to your du système GE de purification de l’eau Rotate refrigerator, the only approved par osmose inversée, seule l’installation Clockwise Install installation is with a GE RVKIT. -
Page 9: Step 3: Install Side Panels
Installation Stainless Steel Built-In Refrigerators • If you choose to use 1/4" side panels, they • Side panels are required whenever the sides of the refrigerator will be exposed and when should be inserted into the case trim as S tep illustrated. -
Page 10: Step 5: Level Refrigerator
Installation Stainless Steel Built-In Refrigerators All models have 4-point leveling. The front is supported by leveling legs, the rear is Step supported by wheels. Hex Nut Adjusts • To level the back of the refrigerator, Leveling Leg Rear Wheels Level turn the 7/16"... -
Page 11: Step 7: Connect Water Supply
Installation Stainless Steel Built-In Refrigerators Check to be sure that refrigerator power cord is not plugged into the wall outlet. Step • Locate and bring copper tubing to the front Connect of the cabinet. • The copper tubing should be just long Water enough to reach the coupling. -
Page 12: Step 10: Arrange Interior
Installation Stainless Steel Built-In Refrigerators • Remove internal packing materials. Step • The freezer compartment shelves are turned upside down for shipping. They must be Arrange removed and turned right side up. To remove shelf packing, apply upward pressure Interior on the inverted shelf with one hand and hold in place. -
Page 13: Step 13: Install Toekick
Installation Stainless Steel Built-In Refrigerators • A standard toekick is supplied. Install with 2 Standard Toekick (Packed with Product) screws provided, adjust to desired height and Step tighten screws. • A custom toekick can be installed to match or complement the surrounding cabinetry. Install 1/4"... -
Page 15: Problem Solving
Door alignment is usually assured when the Value, Home Depot, Servistar, HWI and other Solving refrigerator is leveled. If doors are not aligned leading stores. It is also available through GE after leveling the unit, call for service. Parts by calling 1-800-626-2002. Order part number WX10X15. - Page 16 Note: While performing installations described in this book, safety glasses or goggles should be worn. To obtain specific information concerning any ® Monogram product or service, call GE Answer Center consumer information service at 800.626.2000—any time, day or night. For Monogram local service in your area, call 1-800-444-1845.