Please read and comply with Drive mode Machines with driver cabin these original instructions prior In emergencies, destroy the windows – Danger to the initial operation of your appliance and with a hammer. Risk of injury, risk of damage! store them for later use or subsequent own- Note Danger ers.
Page 4
First close the cylinder valve before Close all cylinder and main valves be- – – Maintenance by expert loosening the pipe or tube connection. fore working in repair workshops and Propellant-operated units are to be – Unscrew and loosen the connection nut protect the gas cylinders against effect checked at regular intervals, at least of the gas cylinder slowly because oth-...
The machine may not be used or stored – Symbols on the machine Symbols in the operating in hazardous areas. It is not allowed to instructions use the appliance in hazardous loca- Risk of burns on account tions. Danger of hot surfaces! Allow the The following applies in general: Keep –...
Operating and Functional Elements Illustration of sweeper Operating field Ignition lock 1 Driver cabin (optional) 2 Cabin door (option) 3 Tank lid 4 Lashing point (4x) 5 Roller brush access 6 Front wheel 7 Side brushes 8 Lighting system (optional) 1 Warning blinking switch (option) 9 Waste container 2 Ignition key...
Multifunction display Before Startup Start up Fold up the cab General notes Read the operating instructions of the In order to perform different tasks, you may have to fold up the cab (optional) first. engine manufacturer before start-up Note: The cab must only be tilted while the and follow the safety instructions care- vehicle is on even ground (±...
Installing a new gas bottle Adjust engine speed Drive the machine Replace the gas cylinder. Set programme selection switch to Observe the installation position of the "Transport drive". gas cylinder. The connection / ring Move the gas lever all the way to the opening must point downwards.
Sweeping dry floors Shutdown Switch on the blower. If the sweeper is going to be out of service for a longer time period, observe the follow- ing points: Park the sweeper on an even surface. Raise the roller brush and the side- ...
Page 10
Safety notes regarding the batteries Maintenance intervals Maintenance Works Please observe the following warning notes Observe the inspection checklist 5.950- Preparation: when handling batteries: Park the sweeper on an even surface. 647.0! Observe the directions on the Turn ignition key to "0" and remove it. Note: The elapsed-time counter shows the battery, in the instructions for timing of the maintenance intervals.
Page 11
Installing and connecting the battery Remove the battery Change the motor oil and the oil filter Insert battery in battery mount. Disconnect pole terminal to negative Caution Screw on mounts on battery base. pole (-). Risk of burns due to hot oil! ...
Page 12
Install new roller brush. The nuts of the Check hydraulic oil level and refill hy- Checking roller brush roller brush must be inserted on the Start the motor. draulic oil notches of the opposite crank. Raise the waste container up to the Note Note: Once the new roller brush has been end-position.
Page 13
Check the tyre pressure Park the sweeper on an even surface. Connect air pressure testing device to tyre valve. Check air pressure and adjust if re- quired. For permissible tyre air pressures see "Technical data". Manually clean the dust filter ...
Changing the headlight bulb (option) EC Declaration of Conformity Unscrew the head lamps. We hereby declare that the machine de- Take out the head lamps and pull out scribed below complies with the relevant the plug. basic safety and health requirements of the Note: Note the positions of the plugs.
Troubleshooting Fault Remedy Appliance cannot be started Sit on the driver seat, the seat contact switch gets activated. Charging or replacing battery Gas bottle empty - replace gas bottle. Gas removal valve closed - open the valve by turning it in anti-clockwise direction. Gas valve iced - please read the description of the gas bottle replacement procedure.
Technical specifications KM 130/300 R LPG Machine data Drive speed, forward km/h Drive speed, reverse km/h Climbing capability (max.) Surface cleaning performance without side brushes 10000 Surface cleaning performance with 1 side brushes 13000 Working width without side brushes 1000...
Page 17
Brake Front wheels mechanical Rear wheel hydrostatic Filter and vacuum system Type Flat fold filter Speed 1/min 2800 Filter surface area, fine dust filter Nominal vacuum, suction system mbar 15,5 Nominal volume flow, suction system Vibrator system Electric motor Working conditions Temperature °C -5 and +40...