Eiki LC-WXL200 Service Manual page 93

Control Port Functions
PIN PORT SIGNAL
U3 CB_IN_PW
V2 CR_IN_PW
Y1 HS2_PW
AB3 ON_5V
AB4 VS2_PW
AG10 FILTER_COUNT
AG11 PW_R/C_FRONT
AG12 EX_PW_UART
AG18 PW_DHS
AH10 PW_R/C_TOP
AH11 PW_R&W_WIRED
AH12 PW_EX_UART
AH18 PW_DVS
AH22 PRESS_SENS
AJ22 LENS_CH_POSI_EX
AK21 WINDS_SENS
AK22 LENS_CV_EX
I/O Expander (TE7783, IC4801)
PIN PORT SIGNAL
3 P2 NET_SW_PW
4 P3 IC_RESET
5 P4 F_MOTOR_SW
6 P5 LENS_LR_SW
7 P6 LENS_UD_SW
8 P7 PJ_UPDATE
9 P8 NET_H/L
49 P22 PROG_B_FRT
50 P23 DDC_SCL
51 P24 DDC_SDA
52 P25 GAMMA_SCL3
53 P26 GAMMA_SDA3
54 P27 USBB_VBUS
61 AIN[1] PF_S1.2V_FRT
62 AIN[2] PF_S5V_MAIN
63 AIN[3] PF_5V_MAIN
64 AIN[4] P_FAIL_LAN
65 AIN[5] ACCELE_SENS1+
66 AIN[6] ACCELE_SENS1-
67 AIN[7] ACCELE_SENS2+
68 AIN[8] ACCELE_SENS2-
72 P31 I/O_PJ_UART
73 P32 PJ_I/O_UART
74 P33 MOUSE_TXD
76 P35 LENS_LR_PWM
77 P36 LENS_UD_PWM
78 P37 MOTOR_STEP
81 DMINUS USB_D-
82 DPLUS USB_D+
91 P11 SCLK_FRT
92 P12 SDAT_FRT
94 P14 BOX_SW
97 P15 W_R/C_SW
98 P16 SILINT
99 P17 INT_FRT
100 P18 DONE_FRT
FUNCTION
CB Signal Input
CR Signal Input
Horiz. Sync Signal Input 2
ON_5V Drive Signal Output
Vert. Sync Signal Input 2
Filter Scroll Count Input
RC Input Front
UART RXD
Horiz. Sync Signal Output
RC Input Top
RC Input Rear and Wired
UART_TXD
Vert. Sync Signal Output
Pressure Sensor Input
Lens Shift H Center Position Detect
Wind Sensor Input
Lens Shift V Center Position Detect
FUNCTION
PJNET Switch Output
Low Power Switch
Filter Motor Drive
Lens Shift LR Switch
Lens Shift U/D Switch
PJNET Firmware update
PJNET
SW_FPGA Config
IIC Bus DDC
IIC Bus DDC
IIC Bus GAMMA
IIC Bus GAMMA
Power Fail Input for S1.2V FRT
Power Fail Input for S5V MAIN
Power Fail Input for 5V MAIN
Power Fail Input for LAN
Acceleration Sensor Input 1+
Acceleration Sensor Input 1-
Acceleration Sensor Input 2+
Acceleration Sensor Input 2-
UART for PJNET
UART for PJNET
PJNET Mouse
Lens Shift L/R Control PWM
Lens Shift U/D Control PWM
Filter Motor Drive
SW FPGA Config
SW FPGA Config
Network Box Switch
Wired Remote Control Detect Input
SW FPGA Config
SW FPGA Config
-88-
I/O NOTE
I
I
I
O
I
I
I
I
O
I
I
O
O
I
I
I
I
I/O NOTE
O
O H: On
O L: Output, H: Stop
O
O L: Down
O H: Normal Mode
O Active L
O
O
I/O
O
I/O
O USB
I
I
I
I
I
I
I
I
O UART
I UART
O UART
O L: Operating, H: Stop
O L: Operating, H: Stop
O PWM
I/O USB
I/O USB
O 3-Wire
O 3-Wire
I L: Detected
I L: Detected
O
I
I