Page 1
Rider's Manual (US Model) R 1200 ST BMW Motorrad...
Page 2
Motorcycle/Retailer Data Motorcycle data Retailer Data Model Contact in Service Vehicle identification number Ms./Mr. Color number Phone number First registration Retailer's address/phone number Registration number (company stamp)
We congratulate you on your authorized BMW motorcycle choice of a motorcycle from retailer will gladly provide BMW and welcome you to the advice and assistance. community of BMW riders. Familiarize yourself with your We hope you enjoy reading new motorcycle so that you this Rider’s Manual and wish...
Electronic immobilizer ... 33 First time out ....54 Hazard warning Before you start .... 55 Welcome to BMW ... 1 flashers ......34 Starting ......58 General information ..4 Tripmaster ....35 Riding ......61 Clock ......
Page 5
Brakes ......91 Riding Clutch ......95 specifications ..... 136 Wheels ......97 9 Service ..... 137 Front-wheel stand ..104 BMW Motorrad Bulbs ......105 service ......138 Jump starting ..... 110 Confirmation of Battery ....... 111 maintenance work ..141 7 Care ......
When the time procedures. your authorized BMW comes to sell your BMW, motorcycle retailer; c Indicates the end of an please remember to hand over optional accessories item of information.
Page 7
Because of this, motorcycle performed either If your BMW was supplied with your motorcycle may differ by an authorized BMW motor- equipment not described in from the information supplied cycle retailer or by a workshop this Rider’s Manual, you will...
Page 8
Rider’s equipment Your authorized BMW motor- cycle retailer can provide infor- Do not ride without the correct mation on the specified clothing. Always wear: Service, Inspection and – helmet Annual Inspection work – motorcycling jacket and needed. trousers – gloves Have all maintenance and –...
General view, left side ....9 General view, right side ....11 Underneath the seat ....13 Handlebar fitting, left ....14 Handlebar fitting, right ....15 Instrument cluster ......16 Headlight ........17 Overview...
General view, right side 1 Seat lock ( 2 Brake-fluid reservoir, rear 3 Vehicle identification number 4 Brake-fluid reservoir, front 5 Case carrier (...
Instrument cluster 1 Speedometer 2 Rev. counter 3 Warning and indicator lights ( 4 Multifunction display 5 Indicator light DWA sensor for lighting of instrument panel 6 Adjuster, clock ( The lighting of the instru- ment panel is equipped with an automatic day and night switchover.c...
Multifunction display Gear indicator Warning and indicator The gear indicator shows lights which gear is selected. If no gear is engaged, the gear indicator displays 0; the ’neu- tral’ indicator light also lights Engine oil temperature The height of the bar indi- cates the engine oil tem- 1 Fuel gauge perature.
Warning indicators Warnings are displayed by means of symbols in the multi- function display. In some cases, an additional general warning light lights up red or yellow. A number of warnings may be issued simultaneously.
Page 24
Overview The warnings are listed in the table below, along with the page numbers of the pages you can refer to for more information. Light Symbol Meaning Explanations Ignition key not authorized Low-beam headlight, high-beam headlight or side light defective Bulb failure.
Page 25
Light Symbol Meaning Explanations Battery is no longer being charged Brake switch defective 1 flash per ABS function not available, as second pull-away test not completed Only residual braking function avail- 4 flashes per able, as ABS self-diagnosis not com- second pleted Control of ABS warning lights...
Page 26
• Have the defective key turn could damage the catalyt- Engine electronics sym- replaced, preferably by an ic converter. bol is displayed. authorized BMW motorcycle Do not run the fuel tank dry.c retailer ( 34). Fault in the engine electronics. • Refuel.
Page 27
If the "engine oil pressure" correct.c cialist workshop, preferably warning is displayed while the • Have the fault rectified by a an authorized BMW motor- motorcycle is being ridden, specialist workshop, prefer- cycle retailer. take account of the traffic situ-...
ABS warnings cialist workshop, preferably rear is displayed. an authorized Rear light or brake light bulb BMW motorcycle retailer. defective. In case of insufficient bat- • Replace bulbs ( 108). tery voltage, the ABS function (...
Page 29
General warning light ing.c cialist workshop, preferably lights up red. an authorized BMW motor- ABS warning light flashes Brake switch defective or cycle retailer. four times per second. incorrectly adjusted. BMW...
Page 30
General warning light and BMW motorcycle retailer. cialist workshop, preferably ABS warning light an authorized BMW motor- General warning light General warning light cycle retailer. lights up red. red. ABS warning light flashes ABS warning light ON.
Page 31
ABS function nor once per second. ing.c the brake booster is available. Fluid level in BMW Integral • Stop and check the thick- Without the ABS func- ABS too low. ness of the brake pads...
Page 32
• Have the fault rectified as – Brake system leaktight, no – Fluid level in the BMW Inte- soon as possible by a spe- signs of brake fluid escap- gral ABS is too low, indi- cialist workshop, preferably ing.
Ignition switch and Switching on ignition Switching off ignition steering lock Keys You receive one master key and one spare key. If a key is lost, please note the informa- tion on the electronic immobi- lizer (EWS) ( 24). Ignition key and steering •...
When you prop the mo- torcycle on the side The electronic immobilizer stand, the surface of the helps protect your BMW ground will determine whether motorcycle from theft, and this it is better to turn the handle- enhanced security is at your bars to the left or right.
You can obtain replacement/ your motorcycle and they are extra keys only through an transmitted via the ring aerial authorized BMW motorcycle in the ignition lock. The ignition retailer. The keys are part of an is not enabled for starting until...
Residual range When you refuel (ignition switched off) the Tripmaster does not register the increase in fuel level unless more than 2 liters are added to the fuel already in the tank. The tank must contain at least 5 liters of fuel for the fuel-gauge reading and the residual range to be »...
Clock Emergency ON/OFF » The hour increments by one each time you press the but- switch Attempting to set the ton. clock while riding the mo- The Emergency ON/OFF • Press button 1 for longer torcycle can lead to accidents. switch is used to switch off the than 2 seconds.
B position while the igni- battery if you are riding at low tion is switched on, the engine speeds. If the charge BMW Integral ABS remains level is low, grip heating is operational ( 73).c switched off to ensure the bat-...
Handlebar levers » Turn counter-clockwise: reach is reduced. Adjusting clutch lever The adjusting screw has Attempting to adjust the a limit position and can clutch lever while riding be turned more easily when the motorcycle can lead to ac- you press the clutch lever for- cidents.
Adjusting handlebars Lights Low-beam headlight The two handlebar halves can Side lights be adjusted to three different The side lights switch on auto- heights. matically when the ignition is switched on. The side lights are a strain on the battery. Do not switch the ignition on for longer than absolutely neces- The low-beam headlight...
Page 43
( 47). • Consult a specialist work- shop, preferably an autho- rized BMW motorcycle • Press the top part of switch 1 retailer, if you are unsure for the high-beam headlight. whether the headlight basic »...
» Left-hand turn indicator switched on. • Have the headlight adjusted » Indicator light for left-hand to the relevant conditions by turn indicator flashes. a specialist workshop, pref- erably an authorized A Neutral position BMW motorcycle retailer. B High load...
Switching off turn Front and rear seats indicators Removing seats • Press right-hand turn indica- tor button 2. » Right-hand turn indicator • Press cancel button 3. • Turn the key clockwise in the switched on. » Turn indicator off. seat lock.
Page 46
• Adjust the seat by removing seat supporting rod 1 and reinserting it in the appropri- ate holder. • When doing so, press the • Lift the driver's seat at the rear seat down. rear and remove it upward. • Lift the seat at the rear and Adjusting front seat release the key.
Page 47
Installing seats If too much pressure is applied in the forward di- rection, there is a danger that the motorcycle will be pushed off its stand. Make sure that the motorcycle is steady on its stand.c • Check that the seat is cor- •...
Helmet holder Mirrors Adjusting mirrors • Use the steel cable from the toolkit to secure the helmet The helmet holders 1 are to the holder: guide the mounted at the rear under the • Move the mirrors into the cable through the helmet rear seat.
Windshield Do not adjust the wind- shield while driving. Adjusting windshield Stop the motorcycle to adjust The windshield can be the windshield.c adjusted to three different Spring preload heights. • Raise or lower the wind- Adjusting spring preload shield by hand as required. for rear wheel »...
To increase spring preload: Your motorcycle's han- • Turn knob 1 in the direction dling will suffer if you do indicated by the HIGH arrow. not match the spring-preload To decrease spring preload: and damping-characteristic • Turn knob 1 in the direction settings.
Harder damping: Your motorcycle's han- The correct tire pressures • Turn adjusting screw 1 in the dling will suffer if you do (measured with tires cold) are: direction indicated by the H not match the spring-preload One-up: arrow. and damping-characteristic –...
Safety instructions ....... 52 Fuel ..........71 Safety check ......... 54 Brake system ........ 72 Riding First time out ......... 54 Before you start ......55 Starting .......... 58 Riding ..........61 Running in ........61 Shifting gears ....... 62 Placing motorcycle on its side stand ......
Safety instructions Alcohol and drugs Do not inhale exhaust fumes. Do not run the engine in an en- Even small amounts of al- Speed closed space.c cohol or drugs will ad- If you ride at high speed, versely affect your perception High voltage always bear in mind that vari- and your ability to assess situ-...
Page 55
Tampering with control – Do not run the fuel tank dry. Flammable materials (e.g. unit of electronic engine- – Do not attempt to start or run hay, leaves, grass, cloth- the engine with a spark-plug ing and luggage, etc.) could management system cap disconnected.
Safety check At regular intervals: The description of the BMW – Engine oil level (every time Integral ABS starts on page Prior to every journey you refuel) ( 73). Use the following checklist to – Brake pads (every second/ BMW Integral ABS incor-...
24). Battery charge current • Emergency ON/OFF symbol is displayed. switch 1 in operating posi- tion A. • Switch on the ignition. » Pre-ride check is performed. » With BMW Integral ABS: ABS self-diagnosis is per- formed.
Page 58
Phase 2 Phase 3 Phase 4 (only with DWA General warning light A warning light defect is The "DWA" battery warn- lights up yellow. displayed. ing for the anti-theft alarm Engine electronics sym- appears if the voltage level of bol is displayed. the batteries in the anti-theft Immobilizer symbol is alarm system...
Page 59
Once the pre-ride check com- 4 times per second. pletes, the various gauges and Self-diagnosis is in progress. indicators show their current The BMW Integral ABS per- values. Phase 2 forms self-diagnosis and a If the engine is started ABS warning light flashes...
Side stand engine. At ambient tempera- BMW Integral ABS remains in You cannot start the motorcycle tures below 32 °F (0 °C), disen- its residual braking function with the side stand extended...
Page 61
The start attempt is auto- matically interrupted if battery voltage is too low. Recharge the battery before you start the engine, or use jump leads and a donor bat- tery to start ( 112).c High engine speeds while the engine is cold accel- erate engine wear.
Troubleshooting chart Fault: Engine does not start at all or is very difficult to start. Possible cause Remedy See page Emergency ON/OFF switch Set the emergency ON/OFF switch to its activated RUN position Side stand extended and gear Retract the side stand fully engaged Gear engaged, clutch not Select neutral or pull clutch lever...
ABS sensors when you will lead to increased engine pull away after starting. The wear. ABS warning light then goes Keep to the guideline values out and the BMW Integral ABS as stated below.c is active.
Brake pads Tires Shifting gears New brake pads must bed New tires have a smooth sur- Engine speed down and therefore do not face. This must be roughened Do not use the high end of the achieve their optimum friction by riding in a restrained manner engine-revolutions range in any levels during the first 500 km.
Page 65
Shifting gears Attempting to shift gears with the clutch engaged can damage the transmission. Always disengage the clutch in order to shift gears.c The gear indicator in the multifunction display tells you which gear is engaged.c...
Placing motorcycle • Turn the handlebars up to The side stand is de- full left lock. signed to support only on its side stand • Check that the motorcycle is the weight of the motorcycle. standing firmly. Do not lean or sit on the mo- If the ground is soft or un- torcycle with the side stand If the motorcycle is on the...
Removing motorcycle • Swing your right leg over the seat and lift the motorcycle from side stand to the upright position. Brake servo assistance is • Hold the motorcycle upright not available when the ig- and balanced. nition is off; the motorcycle •...
Place motorcycle on • Place the full weight of your OE/OA body on the center stand, center stand while pulling the motorcycle to the rear (arrow). If the ground is soft or un- • Check that the motorcycle is even, there is no guarantee standing firmly.
Pushing motorcycle off • Check that the center stand • Make sure the ground is OE/OA has fully retracted. level and firm and place the center stand motorcycle on its center Fuel Brake servo assistance is stand or side stand. not available when the ig- Refueling nition is off;...
Brake system The engine is designed to run General – Premium grade unleaded Descending mountain fuel (98 RON + MON / 2) passes Use fuel of this grade by pref- erence, in order to achieve There is a danger of the rated performance and fuel brakes fading if you use consumption.
Page 75
Bear in mind that this extends means of the integral function, ately because of dirt or mois- your stopping distance, BMW Integral ABS offers ture on the discs or brake improved braking efficiency. pads.
Page 76
ABS is unable to counteract applied. By boosting the brak- ridden in a straight line, the their effects. ing force in this way, BMW Integral ABS is able to BMW Integral ABS achieves handle emergency braking Integral brakes higher braking efficiency than safely.
Page 77
Consequently, ABS does not hydraulic brake boost pro- have to apply considerably intervene until very late, if at all. vided by the BMW Integral more force in order to slow the Under these circumstances ABS is not available in the motorcycle.
Page 78
When the residual brak- ing function is active for both brake circuits, the noise of the pump is no longer audi- ble when you operate the brake levers.c...
These parts and products cient in some circumstances. Supply have been tested by BMW for Use only parts and accesso- The onboard sockets available safety, function and suitability. ries approved by BMW for your...
Page 81
Cable routing The supply to the socket is cut off automatically if battery volt- The cables from the power age is low or the load exceeds socket to the auxiliary device the maximum rating. must be routed in such a way that they: Operating electrical –...
Luggage system • Set spring preload ( 47), damping characteristic Fitting a luggage system will 48) and tire pressures affect the handling of your 49) to suit total weight. motorcycle. The recom- • Make sure that the weight is mended top speed with the uniformly distributed cases loaded is 110 mph between right and left.
Page 84
• Close lid 3 and press it down. Check that nothing is trapped between the lid and the case. • Press the key clockwise (left Closing case case) or counter-clockwise (right case). • Push lever 2 down. » The lever engages. •...
Page 85
Topcase • Unlatch the handle and pull it up as far as it will go. Installing topcase • Locate the case in holders 5 • Lock the topcase. and check that it is securely » The lock opening is horizon- seated.
Page 86
• Push the handle down until it engages. » The topcase is correctly engaged on its carrier. Removing topcase • Lock the topcase. » The lock opening is horizon- tal. • Turn the key clockwise. • Hook the topcase into posi- •...
Page 87
• Press lock barrel 7. Closing topcase » Locking lever 8 pops out. » The lock opening is horizon- • Fully open locking lever 8. tal. • Fully open the locking lever. • Snap the lid of the compart- • Open lid 9. ment closed and push it down.
Page 90
The ’Maintenance’ chapter motorcycle. You can obtain a describes work involving the copy from your authorized replacement of wear parts that BMW motorcycle retailer. can be performed with mini- mum effort. The types of screws used for the components concerned are listed in ( 122).
Engine oil The engine can seize if • Wait 5 minutes after switch- the oil level is low, and ing off the engine. Checking engine oil level this can lead to accidents. • Check the oil level in sight Check the oil level at regular Always make sure that the oil glass.
BMW motorcycle retailer.c bricating oil circuit. They in no Do not ride the motorcycle if way fulfill the function of an oil you have any doubts about the level sensor.
Page 94
» The pressure point must be Checking front brake pad clearly perceptible. thickness » In the case of BMW Integral • Make sure the ground is ABS, the hydraulic pump level and firm and place the Slots are provided in the brake must be heard to run.
Page 95
• Visually inspect the brake erably by an authorized pads from the left to ascer- BMW motorcycle retailer. tain their thickness. Wear indicator 2 indicates the condition of the rear brake pads. The number of rings vis-...
Page 96
– 3 rings: at least 75 % – 2 rings: at least 50 % – 1 ring: 50 to 25 % – No rings visible: Check brake-pad thickness; replace the brake pads if nec- essary. Checking brake fluid level 1 Brake-fluid reservoir, front 3 Brake-fluid reservoir, rear 2 MIN mark 4 MIN mark...
In the event of brake pad tified workshop, preferably cialist workshop, preferably wear, the brake fluid level an authorized BMW motor- an authorized in the brake-fluid reservoir cycle retailer. BMW motorcycle retailer. falls.c...
Page 98
If the position of the cialist workshop, preferably clutch fluid reservoir is an authorized changed, air can enter the BMW motorcycle retailer. clutch system. Do not turn the handlebar fit- The fluid level in the res- ting on the handlebar.c ervoir falls as the clutch wears.c...
Checking rims Have the tires changed in • Make sure the ground is good time before they wear to For each size of tire BMW level and firm and place the the minimum permissible tread Motorrad tests certain makes, motorcycle on its center depth.c...
Page 100
• Pull the front mudguard for- ing parts of the front ward to remove, spreading brakes, particularly the the sides slightly apart at the BMW Integral ABS, in the same time. course of the procedure de- • Force brake pads in brake scribed below.
Page 101
We recom- center stand will lift clear of the mend using the BMW Motor- ground and the motorcycle rad front wheel stand ( could topple to one side.
Page 102
There is a risk of damag- • Ease the brake calipers on to ing parts of the front the brake disks. brake, particularly the BMW Integral ABS, in the course of the procedure de- scribed below. • Roll the front wheel into the front forks.
Page 103
• Install the mudguard and tighten securing screws 1. • Remove the adhesive tape from the wheel rim. The front brakes have to be operated a few times to bed the brake pads against the brake disks. • Install securing screws 2 for •...
Page 104
Removing rear wheel • Remove studs 3 from the rear wheel, while supporting The types of screw used the wheel. are listed on ( 122).c • Place the motorcycle on its center stand. • Remove screw 2 for the bracket of the end muffler from the rear footrest.
Page 105
60 Nm. tighten it at this point. Always have the security of the fasteners checked, preferably an authorized BMW motorcy- cle retailer.c • Turn the end muffler to its ini- A lack of clearance be- tial position.
• Slacken adjusting screws 1. BMW motorcycle retailer. • Push pins 2 apart until the You also need the adapters front suspension fits with the BMW special tool between them. number 363972. • Use locating pins 3 to set the front-wheel stand to the desired height.
Bulbs • Apply uniform pressure to push the front-wheel stand Information on bulbs down and raise the motorcy- The 'bulb defect' symbol cle. appears in the display if a bulb When the motorcycle is is defective. If the brake or rear standing on its center light fails, the symbol is stand: if the motorcycle is...
Page 108
Do not touch the glass of Wear protective goggles and new bulbs with your fin- gloves when changing gers. Use a clean, dry cloth to bulbs.c hold the bulbs when handling Turn the handlebars them. Dirt deposits, in particu- to the left to facilitate lar oil and grease, interfere access.c with heat radiation from the...
Page 109
• When installing, make sure that lug 6 is pointing up and that the bulb is securely seated. • Check that the bulb is cor- rected seated (by looking in through the headlight lens). Replacing side light bulb • Remove bulb 5. •...
Page 110
Installation is the reverse of the • Remove screws 1 on left and • Turn bulb holder 3 counter- removal procedure. right. clockwise to remove it from • Use a clean, dry cloth to hold the bulb housing. the new bulb. •...
Page 111
Replacing rear turn indicator bulb If it is not standing firmly, the motorcycle could topple in the course of the op- erations described below. Make sure that the motorcycle is steady on its stand.c • Remove screw 1. • Turn bulb holder 2 counter- •...
Installation is the reverse of the A short-circuit can result removal procedure. if the crocodile clips of • Use a clean, dry cloth to hold the jump leads are accidental- the new bulb. ly brought into contact with the motorcycle. Jump starting Use only jump leads fitted with fully insulated crocodile clips...
battery, and the other end to Touching live parts of the the negative terminal of the ignition system with the discharged battery. engine running can cause • Start the engine of the vehi- electric shock. cle with the discharged bat- Do not touch parts of the igni- tery in the usual way;...
Page 114
– Keep the surface of the bat- BMW Motorrad has de- • Do not attempt to recharge a tery clean and dry. veloped a trickle-charger completely flat battery via – Do not open the battery. specially designed for com- the onboard socket; instead, –...
Page 115
If the battery is only partially If you are unable to • Charge the battery using a discharged, it can be re- charge the battery via the suitable charger. charged via the onboard power socket, you may be us- • Comply with the operating socket.
Page 116
If it is not standing firmly, the motorcycle could topple in the course of the op- erations described below. Make sure that the motorcycle is steady on its stand.c • Switch off the ignition. • Insert the battery into the battery compartment, with •...
We recommend that you use We recommend that you use braking efficiency. the cleaning and care prod- BMW insect remover to soften After washing the motorcycle, ucts you can obtain from your and wash off insects and stub- dry the brakes by braking.c...
Page 119
Especially in the case of road droppings. BMW vehicle pol- that contain alcohol, solvents salt, carefully clean chrome ish or BMW paint cleaner are or abrasives to clean plastic with plenty of water and BMW recommended here. parts. Even fly-remover pads vehicle shampoo.
• Check the tire pressures engine oil and the oil filter ele- 49). ment changed by a specialist workshop, preferably your au- thorized BMW motorcycle re- tailer. Combine work for stor- ing/restoring to use with a maintenance service or in- spection.c...
One fixed brake disk with 2-piston floating caliper Brake pads Organic brake pads (OE sintered metal) Front suspension Type BMW Telelever Steering lock angle 2 x 42 Front wheel castor in normal-load position 4.4 in (111.6 mm) Rear suspension Type BMW Evo Paralever...
Page 130
Frame and suspension Front suspension system Type Central spring strut with coil spring and single-tube, gas-filled shock absorber Spring travel (bump) 2.4 in (60 mm) Spring travel (rebound) 2 in (50 mm) Total suspension travel (at wheel) 4.3 in (110 mm) Rear suspension system Type Central spring strut with single-tube, gas-filled...
Wheels and tires Front wheel Type Cast wheel with 5 double spokes, MT H2 Rim size 3.50 x 17“ Tire size 120/70 ZR17 Rear wheel Type Cast wheel with 5 double spokes, MT H2 Rim size 5.50 x 17“ Tire size 180/55 ZR17...
HD oil of CCMC classification G4 or G5; amendment PD2 is permissible. Capacity (with filter change) 4.2 quarts (4.0 l) Capacity (without filter change) 3.9 quarts (3.7 l) Top-up volume between MIN and MAX 0.5 quart (0.5 l) BMW recommends Castrol BMW recommends Castrol...
Page 133
Fuel and lubricants Viscosity classes depending on outside temperature -4 °F – 50 °F (-20 °C – 10 °C) SAE 20 32 ° F – 86 °F (0 °C – 30 °C) SAE 30 68 °F (20 °C) – above 86 °F (30 °C) SAE 40 14 °F (-10 °C) –...
Page 134
0.7 quart (0.7 l) Fuel Fuel grade Premium grade unleaded fuel, minimum octane content 98 (RON) Capacity of fuel tank 5.5 gal (21 l) Reserve volume Of that 1 gal (4 l) Brakes Brake fluid DOT 4 We recommend BMW brake fluid...
Electrical system Battery Type 12 V/14 Ah AGM battery, maintenance-free Spark plugs Spark plugs BOSCH YR5LDE Electrode gap 0.0315 in (0.8 mm) Wear limit 0.0394 in (1.0 mm) Fuses All circuits are electronically protected, so plug-in fuses are not necessary. If an electronic fuse trips and de-energizes a circuit, the circuit is active as soon as the ignition is switched on after the fault has been rectified.
Page 136
Electrical system Bulbs Headlight type Dual headlight with free-form technology High-beam headlight H4 halogen bulb 12 V 55 W Low-beam headlight H4 halogen bulb 12 V 55 W Side lights 12 V 5 W Brake/rear light 12 V 21/5W Front turn signals 12 V 21 W Rear flashing turn signals 12 V 10 W...
Dimensions and weights Dimensions Maximum length 85 in (2,165 mm) Maximum width 29.5 in (750 mm) Maximum height: Windshield retracted 48 in (1,220 mm) Windshield extended 49 in (1,255 mm) Seat height 31.89 in/32.68 in (810 mm/830 mm) Wheelbase in normal-load position 59.1 in (1,502 mm) Ground clearance in normal-load position 6.1 in (155 mm)
Riding specifications Speeds Top speed over 124 mph (200 km/h) Acceleration 0-100 km/h 3.5 s Noises Riding noise to EU specification 80 dB (A) Stationary noise to EU specification 87 dB (A) at 3,750 rpm...
To ensure that your BMW is money in the long run. mation on Mobile Service and always in optimum condition, we...
Page 141
Fuel, lubri- BMW Running-in Check (20,000 km) and every further cants and similar substances, fil- The BMW running-in check has 12,000 miles (20,000 km) ters, gaskets etc. are charged to be performed when the (24,000 miles, 36,000 miles, separately.c...
Page 142
BMW Running-In Pre-delivery Check Check Carried out in accordance with manufacturer’s instructions Carried out in accordance with manufacturer’s instructions Odometer reading Brake fluid changed: BMW Integral ABS Wheel circuit Control circuit Date, stamp, signature Date, stamp, signature...
Confirmation of maintenance work BMW Service BMW Service BMW Service BMW Annual Inspection BMW Annual Inspection BMW Annual Inspection BMW Service BMW Service BMW Service BMW Inspection BMW Inspection BMW Inspection Carried out in accordance with Carried out in accordance with Carried out in accordance with manufacturer’s instructions...
Page 144
Confirmation of maintenance work BMW Service BMW Service BMW Service BMW Annual Inspection BMW Annual Inspection BMW Annual Inspection BMW Service BMW Service BMW Service BMW Inspection BMW Inspection BMW Inspection Carried out in accordance with Carried out in accordance with Carried out in accordance with manufacturer’s instructions...
Page 145
Confirmation of maintenance work BMW Service BMW Service BMW Service BMW Annual Inspection BMW Annual Inspection BMW Annual Inspection BMW Service BMW Service BMW Service BMW Inspection BMW Inspection BMW Inspection Carried out in accordance with Carried out in accordance with Carried out in accordance with manufacturer’s instructions...
Page 146
Confirmation of maintenance work BMW Service BMW Service BMW Service BMW Annual Inspection BMW Annual Inspection BMW Annual Inspection BMW Service BMW Service BMW Service BMW Inspection BMW Inspection BMW Inspection Carried out in accordance with Carried out in accordance with Carried out in accordance with manufacturer’s instructions...
Confirmation of service The list is intended as a record of maintenance, warranty and repair work, the installation of optional accessories and, if appropriate, special campaign (recall) work. Record of all work carried out in workshop Work details miles/km Date...
Page 148
Confirmation of service Record of all work carried out in workshop Work details miles/km Date...
Page 149
Confirmation of service Instrument cluster Instrument cluster Instrument cluster replaced replaced replaced at distance at distance at distance _______________________ _______________________ _______________________ (odometer reading) (odometer reading) (odometer reading) ________________________ ________________________ ________________________ Date, stamp, signature Date, stamp, signature Date, stamp, signature...
Page 157
Tire pressure for front wheel - passenger and luggage 36.3 psi, With tire cold Tire pressure for rear wheel - passenger and luggage 42.1 psi, With tire cold BMW Motorrad Order No.: 01 47 7 698 867 BMW recommends 08.2005 2.
Page 158
Please attach this sticker to the inside back cover page of your Rider’s Manual Reporting Safety Defects individual problems between you, your dealer, or BMW of North If you believe that your vehicle has America, LCC. a defect which could cause a crash...
Page 159
Information on BMW Motorrad Integral ABS How does ABS work? resulting in a danger of falling. ensure driving stability when The maximum braking force Before this situation occurs, contact with the road surface which can be transferred to the ABS intervenes and is restored.
Page 160
ON/OFF During driving-safety training Field observations by BMW switch, the light and all elec- courses an unusually high Motorrad show that no com- tronic systems remain...
Page 161
This optimally utilizes the rider to brake the motor- A fault in the BMW Motorrad the dynamic load increase on cycle. Integral ABS is indicated by a the front wheel. At the same...
Page 162
• Always brake with the front How important is regular How is the BMW Motorrad maintenance? Integral ABS designed? and rear brakes Any technical system is The BMW Motorrad Integral • In clear situations, carry out always only as good as...