Denon AVR-2311 Owner's Manual page 63

Setting items
Speaker Config. Surround : Set the presence and size of the surround speakers.
(Continued) • Large : Use a large speaker that can adequately play back low
frequencies.
• Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the surround speakers are not connected.
• When "Surround" is set to "Large", "S.Back" and "F.Height" can be
set to "Large".
• When "Surround" is set to "None", "S.Back" and "F.Height" can
automatically set to "None".
S.Back : Set the presence, size and number of surround back speakers.
• Large : Use a large speaker that can adequately play back low
frequencies.
• Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the surround back speakers are not connected.
• 2spkrs : Use two surround back speakers.
• 1spkr : Use only one surround back speaker. When you select this
setting, connect the surround back speaker to the left (L) channel.
Even when the "S.Back" setting is other than "None", sound may
not be emitted from the surround back speaker, depending on the
playback source. In this case, make "Surround Parameter" – "S.Back"
setting other than "OFF" (vpage 54).
NOTE
When the "Amp Assign" setting (vpage 58) is other than "Normal", you
cannot make the "S.Back" setting.
F.Height : Set the presence and size of the front height speakers.
• Large : Use a large speaker that can adequately play back low
frequencies.
• Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the front height speakers are not connected.
NOTE
When the "Amp Assign" setting (vpage 58) is other than "Front Height",
you cannot make the "F.Height" setting.
Remote control operation
buttons
Setting details
Move the cursor
(Up/Down/Left/Right)
Setting items
Bass Setting SW Mode : Select low range signals to be reproduced by subwoofer.
Set subwoofer and LFE • LFE : The low range signal of the channel set to "Small" speaker size is
signal range playback. added to the LFE signal output from the subwoofer.
• LFE+Main : The low range signal of all channels is added to the LFE
signal output from the subwoofer.
• "SW Mode" can be set when "Speaker Config." – "Subwoofer"
(vpage 58) is set to "Yes".
• Play music or a movie source and select the mode offering the strongest
bass.
• Select "LFE+Main" if you want the bass signals to always be produced
from the subwoofer.
NOTE
If "Front" and "Center" for "Speaker Config." are set to "Large", and "SW
Mode" is set to "LFE", no sound may be output from the subwoofers,
depending on the input signal or selected surround mode.
LPF for LFE : Set LFE signal playback range.
• 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz
Distance Unit : Set the unit of distance.
Set distance from listening • Meters / Feet
position to speakers.
Step : Set the minimum variable width of the distance.
Measure beforehand the
• 0.1m / 0.01m
distance from the listening
• 1ft / 0.1ft
position to each speaker.
Front L / Front R / Center / Subwoofer / Surround L / Surround R /
S.Back L z / S.Back R
z When the "Speaker Config." – "S.Back" setting (vpage 59) is set to
"1spkr", "S.Back" is displayed.
• 0.00m – 18.00m / 0.0ft – 60.0ft : Set the distance.
• The speakers that can be selected differ depending on the "Amp Assign"
(vpage 58) and "Speaker Config." (vpage 58) settings.
• Default settings :
Front L / Front R / Center / Subwoofer / F.Height L / F.Height R : 3.6 m
(12.0 ft)
Surround L / Surround R / S.Back L / S.Back R : 3.0 m (10.0 ft)
• Set the difference in the distance between the speakers to less than
6.0 m (20 ft).
NOTE
Speakers set to "None" in "Speaker Config." (vpage 58) are not
displayed.
Confirm the setting
Manual Setup
Setting details
z / F.Height L / F.Height R : Select the speaker.
Return to previous menu
ENGLISH
59