Denon AVR-2311 Owner's Manual page 58

ENGLISH
Audio/Video Adjust
Setting items
n For 2-channel sources
S.Back
Sets the method of
ON : The surround back channel is used.
generating of the surround
OFF : No signal is played from the surround back channels.
back channel.
n For Multi-channel sources
Set the decoding method for the surround back channel.
DSCRT ON : Play the surround back signals included in the 7.1-channel
source.
MTRX ON : Generate and play the surround back signals from the
surround channel signals.
ES MTRX
surround channel signals of the DTS source.
ES DSCRT
6.1-channel DTS source.
PLgx C
the signals in the Dolby Pro Logic gx Cinema mode.
PLgx M : Generate and play the surround back signals by decoding the
signals in the Dolby Pro Logic gx Music mode.
OFF : Do not play the surround back channel.
z1 This can be selected when playing DTS sources.
z2 This can be selected when playing DTS sources including a signal to
identify discrete 6.1-channel signals.
z3 This can be selected when "Speaker Config." – "S.Back" (vpage 59)
is set to "2spkrs".
• This can also be set by pressing
• If the source being played contains a surround
back signal, the decoder type is automatically
selected by the AFDM function. Set "AFDM" to
"OFF" to switch to your preferred decoder.
NOTE
If the setting in "Speaker Config." – "S.Back" (vpage 59) is "None",
"S.Back" is not displayed.
ON : Audio is output from the front height speaker.
F.Height
Determine whether to use OFF : Audio is not output from the front height speaker.
front height channel.
NOTE
• "F.Height" is displayed for the following settings.
• When "Amp Assign" (vpage 58) is set to "Front Height".
• When the "Speaker Config." – "F.Height" setting (vpage 59) is set to
other than "None".
• "F.Height" cannot be set if the HD Audio source being played includes a
front height channel. In this case, the Front height channel is played back
without decoding in PLgz mode, using the input signal.
54
Remote control operation
buttons
Setting details
z1
: Generate and play the surround back signals from the
z2 : Play the surround back signals included in the
z3
: Generate and play the surround back signals by decoding
STANDARD
.
Move the cursor
(Up/Down/Left/Right)
Setting items
Height Gain Low : Reduce the front height channel volume.
Control the front height Mid : Front height channel sound is output with standard sound volume.
channel volume. High : Increase the front height channel volume.
NOTE
"Height Gain" is displayed for the following settings.
• When "Amp Assign" (vpage 58) is set to "Front Height".
• When the "Speaker Config." – "F.Height" setting (vpage 59) is set to
other than "None".
• When surround mode is "PLgz" or the PLgz decoder is used.
Subwoofer ON : The subwoofer is used.
Turn subwoofer output on OFF : The subwoofer is not used.
and off.
NOTE
This can be set when the surround mode is "DIRECT" (vpage 31), "PURE
DIRECT" (vpage 31) and the "SW Mode" (vpage 59) is "LFE+Main".
Default Yes : Reset to the defaults.
The "Surround Parameter" No : Do not reset to the defaults.
settings are returned to the
default settings.
n Tone
Adjust the tonal quality of the sound.
Setting items
Tone Control ON : Allow tone adjustment (bass, treble).
Set the tone control function OFF : Playback without tone adjustment.
to ON and OFF.
"Tone Control" can be set when "Dynamic EQ" (vpage 55) is set to
"OFF".
NOTE
• "Tone Control" settings are not reflected to ZONE2.
• The tone cannot be adjusted in the direct mode.
Bass –6dB – +6dB
Adjust low frequency range
"Bass" can be set when "Tone Control" is set to "ON".
(bass).
Treble –6dB – +6dB
Adjust high frequency range
"Treble" can be set when "Tone Control" is set to "ON".
(treble).
Confirm the setting
Setting details
Setting details
Return to previous menu