Worx Sonicrafter WX677 Safety And Operating Manual
  1. Manuals
  2. Brands
  3. Worx Manuals
  4. Power Tool
  5. Sonicrafter WX677
  6. Safety and operating manual
Worx Sonicrafter WX677 Safety And Operating Manual

Worx Sonicrafter WX677 Safety And Operating Manual

High frequency multi-function tool
Hide thumbs Also See for Sonicrafter WX677:
Table of Contents

Advertisement

Quick Links

Download this manual
SAFETY AND OPERATING MANUAL
High Frequency
WX677
Multi-function Tool

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sonicrafter WX677 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Worx Sonicrafter WX677

Summary of Contents for Worx Sonicrafter WX677

  • Page 1 SAFETY AND OPERATING MANUAL High Frequency WX677 Multi-function Tool...

  • Page 2: General Power Tool Safety Warnings

    GENERAL POwER TOOL electric shock. f) If operating a power tool in a damp SAFETY wARNINGS location is unavoidable, use a residual current device (RcD) protected WARNING: Read all safety warnings supply. Use of an RCD reduces the risk of and all instructions.
  • Page 3 4) PoWeR tool USe AND cARe b) Use power tools only with specifically designated battery packs. a) Do not force the power tool. Use the correct power tool for your Use of any other battery packs may create application. The correct power tool will a risk of injury and fire.
  • Page 4 Your risk from these exposures varies, k) After extended periods of storage, it may be necessary to charge depending upon how often you do this type and discharge the battery pack of work. To reduce your exposure to these several times to obtain maximum chemicals: performance.
  • Page 5 SYMbOLS To reduce the risk of injury, user must read instruction manual. Warning Wear eye protection Wear ear protection Wear dust mask Do not dispose of batteries, Return exhausted batteries to your local collection or recycling point. Do not expose to rain or water Do not burn C-tick marking High Frequency Multi-function Tool...
  • Page 6 On/Off Switch Battery Pack Light Variable Battery Pack Universal Fit Venting Speed Dial Latch Accessory Slots Interface* Flange Smaller flange for other brands’ sanding pads Allen Key * Works with other oscillating tool brands’ accessories. The following compatible brands are trademarks owned by third parties which may be registered by their respective owners: Bosch , Black &...

  • Page 7: Technical Data

    TEcHNIcAL DATA Voltage Oscillations speed 5000-20000/min Oscillations angle 3.2° Machine weight High Frequency Multi-function Tool...

  • Page 8: Mounting Accessories

    OPERATION INSTRUcTIONS Note: Before using the tool, read the instruction book carefully. INteNDeD USe The power tool is intended for sawing and separating wooden materials, plastic, plaster, non-ferrous metals and fasteners (e.g. nails and clamps) as well as for working on soft wall tiles and for dry grinding of small surfaces.
  • Page 9 Note: For prior model WORx Sonicrafter hex-interface accessories and most other non-WORx branded accessories, the Flange must be completely removed to install accessory (See Fig. D). 2. MoUNtING/cHANGING tHe SANDING SHeet (See fig. e) Align the sanding sheet and press it onto the sanding pad by hand.

  • Page 10: Operating The On/Off Switch

    3. MoUNtING tHe SUctIoN DevIce (See fig. f1-f5) When vacuuming, mount the suction device as shown in F1-F5. Note: Using the sanding pad perforated. You can only do the vacuuming after fitting the dust collector. 4. oPeRAtING tHe oN/off SWItcH To start the machine, push the On/Off switch forward so that the “I”...
  • Page 11 6. ReMove oR INStAll BAtteRy PAck (See fig. G) Depress the Battery Pack Latches on both sides to release Battery Pack. After recharging, insert the Battery Pack into battery port. A simple push and slight pressure will be sufficient. 7. leD lIGHt The sight light allows you to keep a clear view under less illuminated circumstances.
  • Page 12 APPLIcATION WARNING: the sawing teeth are very sharp. Do not touch during mounting and application. The workpiece must be clamped tightly before it is cut. Name Application Wood, plastic, fiberglass, Universal Metal/Wood End Cut nails, non-ferrous metals, thin Blade. sheet metal, hardened fillers. Standard Wood End Cut Blade.

  • Page 13: Maintain Tools With Care

    DISPOSAL OF AN MAINTAIN TOOLS wITH EXHAUSTED bATTERY cARE PAck Your power tool requires no additional lubrication or maintenance. There are no user To preserve natural resources, serviceable parts in your power tool. Never please recycle or dispose of use water or chemical cleaners to clean your the battery pack properly.
  • Page 16 Copyright © 2013, Positec. All Rights Reserved. 2PGA80APK11021A0...

Table of Contents