Subscribe to Our Youtube Channel
Related Manuals for Worx Sonicrafter WX676
Summary of Contents for Worx Sonicrafter WX676
- Page 1 物料号：２ＰＧＡ８０ＡＰＫ１１０１４Ａ１ 材料：100克双胶纸 颜色：1色（黑） 尺寸：A5 页数：16P 装订方式：骑马钉 备注： 特别提示： 此小页为说明书印刷要求，不需要输出菲林, 不作为印刷内容。...
- Page 2 SAFETY AND OPERATING MANUAL ORIGINAL INSTRUcTIONS Oscillating tool WX676 WX676.5 WX676.7...
-
Page 3: General Power Tool Safety Warnings
GENERAL POwER TOOL f) If operating a power tool in a damp location is unavoidable, use SAFETY wARNINGS a residual current device (RcD) protected supply. Use of an RCD WARNING: Read all safety warnings and all instructions. Failure to follow reduces the risk of electric shock. - Page 4 4) PoWeR tool USe AND cARe ensure that the safety of the power tool is a) Do not force the power tool. Use maintained. the correct power tool for your b) If the replacement of the supply cord application. The correct power tool will is necessary, this has to be done by the manufacturer or his agent in do the job better and safer at the rate for...
- Page 5 SYMBOLS To reduce the risk of injury, user must read instruction manual Warning Double insulation Wear eye protection Wear ear protection Wear dust mask Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
- Page 6 Variable On/Off Switch Speed Dial Universal-Fit Accessory Interface* Venting Slots Small Flange Flange For other brands' sanding pads *Works with other oscillating tool brands' accessories. The following compatible brands are trademarks owned by third parties which may be registered by their respective owners: Bosch , Black &...
-
Page 7: Technical Data
TEcHNIcAL DATA Type WX676 WX676.5 WX676.7 (6-designation of machinery, representative of high frequency oscillation tool) Voltage 220-240V~50/60Hz Power input 250W Oscillation speed 11000-20000/min Oscillation angle 3.2° Protection class Machine weight 1.4kg NOISE INFORMATION A weighted sound pressure : 85dB(A) A weighted sound power : 96dB(A) &K 3.0dB(A) - Page 8 this tool may cause hand-arm vibration syndrome if its use is not adequately managed. WARNING: To be accurate, an estimation of exposure level in the actual conditions of use should also take account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle but not actually doing the job.
-
Page 9: Operation Instructions
Accessory Interface.(See Fig. B) -tighten the flange - Use the Allen Key to rotate the Flange counterclockwise until accessory is tightened securely.(See Fig. C) Note: For prior model WORx Sonicrafter hex-interface ® accessories and most other non-WORx branded accessories, the Flange must be completely removed to install accessory (See Fig. - Page 10 2. MoUNtING / cHANGING tHe SANDING SHeet (See fig. e) Align the sanding sheet and press it onto the sanding pad by hand. Firmly press the power tool with the sanding sheet against a flat surface and briefly switch the power tool on.
- Page 11 8. SAWING WItH tHe UNIveRSAl eND cUt SAW BlADe (See fig. k) WARNING: the sawing teeth are very sharp. Do not touch during mounting and application. The workpiece must be inserted firmly or clamped tightly before it is cut. Typical application: wood, metal (e. g. nails),plaster board and soft plastics.
- Page 12 APPLIcATION WARNING: the sawing teeth are very sharp. Do not touch during mounting and application. The workpiece must be clamped tightly before it is cut. Name Application Wood, plastic, fiberglass, Universal Metal/Wood End Cut nails, non-ferrous metals, thin Blade. sheet metal, hardened fillers. Standard Wood End Cut Blade.
-
Page 13: Maintenance
wORKING HINTS FOR YOUR ENVIRONMENTAL TOOL PROTEcTION If your power tool becomes too hot, especially Waste electrical products should not when used at low speed, set the speed to be disposed of with household waste. maximum and run it with no load for 2-3 Please recycle where facilities exist. -
Page 14: Plug Replacement
Positec Power Tools (Europe) Ltd, PO Box 152, Leeds, LS10 9DS, UK IMPoRtANt The wires in the mains lead are colored in Declare that the product, Description WoRX oscillating tool accordance with the following code: Blue – Neutral Type WX676 WX676.5 WX676.7 Brown – live... - Page 17 Copyright © 2013, Positec. All Rights Reserved. 2PGA80APK11014A1...
Need help?
Do you have a question about the Sonicrafter WX676 and is the answer not in the manual?
Questions and answers