Ac1200 wireless dual band gigabit router (147 pages)
Summary of Contents for TP-Link M7350
M7350 LTE-Advanced Mobile WiFi REV 2.0.0 1910011264...
Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE STATEMENT CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device is restricted to indoor use only when operating in the 5150 to 5250 MHz frequency range.
5150-5250 MHz Country Restriction Reason/remark Bulgaria Not implemented Planned Croatia License required General authorization required if used outside own Italy premises General authorization required for network and service Luxembourg None supply (not for spectrum) Russian No info Federation RF Exposure Information (SAR) This device meets the EU requirements (1999/519/EC) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Safety Information When product has power button, the power button is one of the way to shut off the product; When there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: LTE-Advanced Mobile WiFi Model No.: M7350 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:...
Make sure that the package contains the above items. If any of the listed items is damaged or missing, please contact your distributor. Conventions The Device or M7350 mentioned in this guide stands for M7350 LTE-Advanced Mobile WiFi without any explanation.
Chapter 1. Introduction 1.1 Product Overview TP-LINK’s M7350 is at the forefront of wireless 4G sharing. Just insert a 4G SIM card into the device to instantly establish a selectable dual band Wi-Fi hotspot. With up to 150Mbps download and 50Mbps upload speeds, the M7350 is able to provide 4G wireless sharing to up to 15 users simultaneously.
M7350 LTE-Advanced Mobile WiFi User Guide 1.3 Physical Description Figure 1-1 the Exterior The details about the Exterior are explained as below. MENU button: Press this button to enter the menu screen or scroll down. You can also press this button until the screen appears to start WPS.
M7350 LTE-Advanced Mobile WiFi User Guide Internet connection Indicates the successful network connection. Data Roaming Indicates you are in roaming service. Displays the Wi-Fi status and the amount of current Wi-Fi connection wireless clients. Indicates that there is un-read short message(s) and the amount of un-read messages.
M7350 LTE-Advanced Mobile WiFi User Guide Chapter 2. Hardware Installation 2.1 Environment Requirements Place the Device in a well-ventilated place far from any heater or heating vent Avoid direct irradiation of any strong light (such as sunlight) Keep at least 2 inches (5 cm) of clear space around the Device ...
1) Touch the metal contacts of the battery to the metal points of the Device, and then press to fit the battery body into the slot. 2) Close the cover by pressing it. STEP 3: Turn on the M7350 Hold the button until the screen appears as shown below. (You can also hold the...
“Power Off” to turn off the M7350). Charging your M7350 Via the power adapter Via the computer USB Note: 1. Your M7350 has been fully charged when the lighting symbol ( ) of battery icon disappeared. 2. Recommend using the provided power adapter.
M7350 LTE-Advanced Mobile WiFi User Guide Chapter 3. Quick Installation Guide This chapter will guide you to quickly set up the basic functions for your M7350. 3.1 System Requirements SIM card with Internet access enabled. Computer supports the 2.4GHz/5GHz wireless band.
M7350 LTE-Advanced Mobile WiFi User Guide Note: The default SSID (also called Wireless Network Name) of the device is TP-LINK_M7350_XXXXXX. (XXXXXX is the last 6 characters of the device’s MAC address.) You can check the SSID and Password on the screen or rear cover label.
When Connected appears behind the SSID of M7350, you’ve successfully connected to its wireless network. Note: After successful connection to M7350 (with a SIM card inserted), you can enjoy the 4G mobile connection instantaneously. If not, please refer to and retry. 3.4 Quick Setup 3.4.1 Quick Setup via your phone...
M7350 LTE-Advanced Mobile WiFi User Guide After successful login, there will appear the following page. You can set up a new login username and password on this page, and click Done to continue. On the Wireless page, you can create a unique and easy-to-remember wireless network name (SSID) as well as Wireless Password, or you can keep it default.
M7350 LTE-Advanced Mobile WiFi User Guide the policy of local government and your requirements. 3.4.2 Quick Setup via your PC Open a web-browser, enter the default address http://tplinkmifi.net or http://192.168.0.1 in the Address field and then press Enter. When the login window appears, enter admin (in lower case letters) for both Username and Password, and then click the Login button or press the Enter.
M7350 LTE-Advanced Mobile WiFi User Guide Note: If the above screen does not pop-up, it means that your Web-browser has been set to a proxy. Go to Tools menu > Internet Options > Connections > LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.
M7350 LTE-Advanced Mobile WiFi User Guide Wizard – Dial-up Settings Figure 3-3 On the Wireless Settings page, you can create a unique and easy-to-remember wireless network name (SSID) as well as Wireless Password, or you can keep it default. Choose your region from the drop-down list and choose the wireless band.
M7350 LTE-Advanced Mobile WiFi User Guide Wizard – Finish Figure 3-5 -15-...
LTE-Advanced Mobile WiFi User Guide Chapter 4. Device Configuration After the successful login to the web-based management page of M7350, you will see the main menu listing Wizard, Status, SMS and Advanced on the top. In the following parts, these items will be explained in details, about their respective functions and configurations.
M7350 LTE-Advanced Mobile WiFi User Guide Statistics: Displays the device's data usage statistics, including the data monthly used/total used and the data daily used. The data usage accounting may differ from your carrier's, and it is subject to your carrier's statistics.
M7350 LTE-Advanced Mobile WiFi User Guide Click Refresh to refresh the inbox, and get any new message. Click Delete to delete the message(s) select. 4.3.2 New Message Figure 4-5 New Message Phone Number: Enter the receiver’s phone number. Content: Text your message in this box. The message you are texting is limited to 160 ...
M7350 LTE-Advanced Mobile WiFi User Guide Click Delete to delete the message(s) you select. 4.3.4 Draft Box You can review the unsent saved message(s) on this page. Figure 4-7 Draft Box Phone Number: Shows the phone number that this message was planned to be sent to.
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-9 Settings Message Center: Disabled by default. Do not enable it unless you want to manually set the message center number. Message Center Number: When the Message Center is enabled, you can enter the ...
M7350 LTE-Advanced Mobile WiFi User Guide 4.4.1 Dial-up Dial-up Menu Figure 4-11 220.127.116.11. Dial-up Settings You can configure dial-up settings on this page. Dial-up Settings Figure 4-12 Mobile Data: It is enabled by default. You can disable it to prohibit Internet access.
M7350 LTE-Advanced Mobile WiFi User Guide APN: Access Point Name, provided by your ISP. You need to set APN only after selecting the static APN type. You are recommended to keep the default value. Username/Password: Enter the username and password provided by your ISP. These ...
M7350 LTE-Advanced Mobile WiFi User Guide Network Mode Settings Figure 4-14 Network Mode: The device supports three modes of network connection - 4G Preferred, 4G Only, and 3G only. If your SIM card supports WCDMA, select 3G only; if your SIM card supports FDD-LTE, select 4G Preferred or 4G only as you need.
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-15 PIN Management SIM Card Status: Shows the status of your SIM card. PIN Management: You can select whether to enable this function or not. Once the PIN code function is enabled, every time you start the device with this SIM card inserted, you need to enter the PIN code.
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-16 PIN Configuration - PUK Decode A PUK (PIN Unlocked Key), also known as Personal Unlock Code (PUC), is used in 3GPP mobile phones to reset a personal identification number (PIN) that has been lost or forgotten.
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-18 Wireless Basic Settings Wireless Network Name (SSID): SSID is short for Service Set Identification, which helps you distinguish different wireless networks. The default SSID of this device is TP-LINK_M7350_XXXXXX (XXXXXX stand for the last 6 characters of the MAC address of it.).
M7350 LTE-Advanced Mobile WiFi User Guide Wireless Mode: This field determines which Wi-Fi network protocol will be used. The wireless mode list varies with the wireless band. For 2.4GHz wireless band, the wireless mode can be 11n only, 11bg mixed and 11bgn mixed. For 5GHz wireless band, the wireless mode can be 11n only and 11an mixed.
M7350 LTE-Advanced Mobile WiFi User Guide WPS: Choose PBC or choose PIN and enter the PIN code to the root device, and then click Start. PBC: Push Button Configuration. You need to start WPS (by hardware or software) on ...
M7350 LTE-Advanced Mobile WiFi User Guide 18.104.22.168. Black List The Black List page displays the basic information about the Wi-Fi clients that have been blocked. Figure 4-21 Black List ID: The index of the Wi-Fi client. Client Name: The name of the Wi-Fi client.
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-22 DHCP Server DHCP Server: You can select to enable or disable the DHCP server. If you disable the server, you must have another DHCP server within your network or else you must configure the IP address of the computer manually.
M7350 LTE-Advanced Mobile WiFi User Guide 4.4.4 Data Settings You can configure data settings on this page. Figure 4-23 Data Settings Total/Monthly Used: Total/Monthly data used. You can click Correct and input the actual data amount to correct the data.
If you have chosen the Wi-Fi access mode, please refer to the following steps to visit the Micro-SD storage sharing. For Windows device: Connect your computer to M7350 wirelessly. Open Run in your computer and input the IP address of your M7350. Here is “\\192.168.0.1” by default. Then click OK to continue. -32-...
M7350. Here we Micro-SD storage take “ES File Explorer” as an example. 1) Connect your device to M7350 wirelessly. 2) Open ES File Explorer and click New. 3) Set type as samba (LAN) and input the IP address of your M7350. -33-...
Micro-SD storage sharing. For IOS device: You need to use some APPs to access the in your M7350. Here we Micro-SD storage take “AcePlayer” as an example. 1) Connect your device to M7350 wirelessly. 2) Open AcePlayer and click Media Explorer. -34-...
M7350 LTE-Advanced Mobile WiFi User Guide 3) Select samba servers. 4) Click +. 5) Input the IP address, login username and password of your M7350. 6) Click the device button to visit the Micro-SD storage sharing. Note: 192.168.0.1 is the device’s default IP address. You can go to “Advanced -> DHCP Server”...
M7350 LTE-Advanced Mobile WiFi User Guide 4.4.6 Device Figure 4-25 Device menu Under Device menu, you can do such configurations as restoring all the settings of the device to its factory defaults, rebooting the device, and checking some information about the device.
Update via the local server: Update your firmware by using the update file that has been downloaded from website www.tp-link.com. Click Browse to select the update file on your local computer. Click Update to update the firmware. 22.214.171.124. Factory Defaults You can restore the device to its factory default settings when necessary.
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-28 Account Management Old Username: The old username that is used to log in to the device. Old Password: The old password that is used to log in to the device. ...
M7350 LTE-Advanced Mobile WiFi User Guide 126.96.36.199. Shutdown Figure 4-29 Shutdown Click Reboot to reboot the device. Click Power Off to shut down the device. 188.8.131.52. Time Settings Figure 4-30 Time Settings Time Zone: Select your local time zone. ...
M7350 LTE-Advanced Mobile WiFi User Guide Time: Display your local time. Click Save to save your settings. 184.108.40.206. System log This page displays the device's information about system logs, including log ID, time, type, level, content, and debug log.
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-32 Device Information Model: The model of the device. Firmware Version: The current firmware version. Hardware Version: The current hardware version. IMEI: International Mobile Equipment Identity. Composed of 15 digits, it is unique and thus ...
LTE-Advanced Mobile WiFi User Guide Appendix A: FAQ FAQ1. What should I do if I cannot log into the web-management page? Verify that your device is connecting to the M7350. Verify that you entered the correct IP address http://tplinkmifi.net or http://192.168.0.1.
8. But in windows XP, you will need to install the driver manually. For windows XP: Step 1: After you have connected your M7350 to a windows XP computer via USB, there will be a popup window like this. Choose "no, not this time" and click next.
Step 3: Choose "Don't search. I will choose the driver to install." and click next. Step 4: Click Next to continue. Step 5: Choose "Have Disk -> Browse". Then choose the driver you have downloaded from TP-LINK website and click Open. -44-...
M7350 LTE-Advanced Mobile WiFi User Guide Step 6: Click OK to continue. Step 7: Click Next to continue. Step 8: You may get a warning like this. Please just ignore it. -45-...
M7350 LTE-Advanced Mobile WiFi User Guide Step 9: Click Finish, then this windows XP computer will be able to go to Internet. -46-...
M7350 LTE-Advanced Mobile WiFi User Guide Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows 7. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed.
M7350 LTE-Advanced Mobile WiFi User Guide Click the right button, and Select Properties. In the prompt page that showed below, double click on the Internet Protocol Version 4 (TCP/IPv4). -48-...
M7350 LTE-Advanced Mobile WiFi User Guide The following Internet Protocol Version 4 (TCP/IPv4) Properties window will display and the IP Address tab is open on this window by default. You have two ways to configure the TCP/IP protocol below: Setting IP address automatically...
M7350 LTE-Advanced Mobile WiFi User Guide Setting IP address manually a. Select Use the following IP address radio button. And the following items available. b. If the Device's LAN IP address is 192.168.0.1, type IP address is 192.168.0.x (x is from 2 to 254), and Subnet mask is 255.255.255.0.
M7350 LTE-Advanced Mobile WiFi User Guide Now click OK to keep your settings. -51-...
M7350 LTE-Advanced Mobile WiFi User Guide Appendix C: Specifications General Standards IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n 4G:FDD-LTE Network Type 3G: DC-HSPA+/HSPA/UMTS 2G: EDGE/GRPS/GSM Certification CE, RoHS Dimension 4.2 × 2.6 × 0.6 in. (106 × 66 × 16mm)
M7350 LTE-Advanced Mobile WiFi User Guide Appendix D: Glossary 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding.