Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zanussi ZGL640TW
Summary of Contents for Zanussi ZGL640TW
- Page 1 User manual ZGL640TW ZGL640ITX...
-
Page 2: Table Of Contents
• Keep the minimum distance from the other • Make sure the appliance is installed correct- appliances and units. ly. Loose and incorrect electricity mains ca- www.zanussi.com... - Page 3 Always lift these ob- • Do not let the appliance stay unattended jects up when you have to move them on the during operation. cooking surface. www.zanussi.com...
-
Page 4: Product Description
Cooking surface layout Semi-rapid burner Semi-rapid burner Control knobs Spark generator button Auxiliary burner Rapid burner Control knobs Symbol Description ignition position / maxi- Symbol Description mum gas supply no gas supply / off posi- tion minimum gas supply www.zanussi.com... -
Page 5: Daily Use
Warning! Always turn the flame down or switch it off before you remove the pans from the burner. Helpful hints and tips Energy savings Warning! Refer to "Safety information" chapter. • If possible, always put the lids on the pans. www.zanussi.com... -
Page 6: Care And Cleaning
They must be washed by hand. from damage. After cleaning, dry the appliance with a soft • When you wash the pan supports by hand, cloth. take care when you dry them as the enamel- www.zanussi.com... -
Page 7: Troubleshooting
5 seconds. The gas ring burns unevenly • Burner crown is blocked with • Make sure that the injector is food residues not blocked and the burner crown is clear of food particles. www.zanussi.com... -
Page 8: Installation
10 m³ an air vent of effective area of 50 For appliances installed in the Republic of Ire- cm² is required, while if the volume exceeds 11 land please refer to NSAI- Domestic Gas In- m³ no air vent is required. www.zanussi.com... - Page 9 (copper with mechanical end). as shown in the diagram. Screw the parts to- gether without using excessive force. Injectors replacement 1. Remove the pan supports. 2. Remove the caps and crowns of the burn- www.zanussi.com...
- Page 10 • Do not pull the mains cable to disconnect that no part of it reaches a temperature of 50° the appliance. Always pull the mains plug. C higher than the ambient temperature. If it is www.zanussi.com...
- Page 11 'L'. It must always be connected to the network phase. There must be no cut or stray strands of wire present. The cord clamp must be correctly at- tached to the outer sheath. www.zanussi.com...
-
Page 12: Technical Information
Auxiliary burner: 1.0 kW Length: 500 mm TOTAL POWER: G20 (2H) 20 mbar = 8 Hob recess dimensions G30 (3+) 28-30 mbar = 567 g/h Width: 500 mm G31 (3+) 37 mbar = Length: 470 mm 557 g/h Heat input www.zanussi.com... -
Page 13: Gas Burners
NORMAL DUCED NATURAL GAS POWER (Butane/Propane) G30/G31 (3+) POWER G20 (2H) 20 mbar 28-30/37 mbar BURNER 28–30 inj. 1/100 inj. 1/100 37 mbar m³/h mbar Auxiliary 0.33 0.095 Semi-rapid 0.45 0.190 3.0 (natural Rapid gas) 0.75 0.286 2.8 (LPG) www.zanussi.com... - Page 14 www.zanussi.com...
- Page 15 www.zanussi.com...
- Page 16 www.zanussi.com/shop...