Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Opticon DFM 1000
Summary of Contents for Opticon DFM 1000
- Page 1 User’s Manual DFM 1000...
- Page 2 Under all circumstances this manual should be read attentively, before installing and or using the product. In no event, Opticon Sensors Europe will be liable for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages.
-
Page 3: Table Of Contents
’ DFM1000 S MANUAL CONTENTS page page PIN OUT INTRODUCTION SPECIFICATIONS INSTALLATION 6.1. Electrical specifications NPACKING Optical specifications Supported symbologies ETAILED VIEW Functionality 2.2.1 Dimensions of the scanner Environmental specifications 2.2.2 Details of the scanner Physical specifications ANDLING PRECAUTIONS TROUBLESHOOTING OUNTING PRODUCT ORDERING 2.4.1... -
Page 4: Introduction
’ DFM1000 S MANUAL INTRODUCTION INSTALLATION The DFM1000 bar code laser scanner has 2.1 UNPACKING been specifically developed for industrial use. The rugged metal housing can easily be fixed through an adapter on a DIN rail. When you remove the packing, please check The high scan rate makes the scanner for any physical damage. -
Page 5: Detailed View
’ DFM1000 S MANUAL 2.2 DETAILED VIEW 2.2.1 Dimensions of the scanner 143 mm 105 mm 2.2.2 Details of the scanner 1. Reading window Reads bar codes Never obstruct this window. 2. Autotrigger aperture It is very important that the autotrigger aperture always can operate free. -
Page 6: Handling Precautions
The DFM1000 is water-, dust- and schock the cradle. So do not try to resistant according to the specifications in the take it apart. Opticon will not appendix, but the scanner consists of minute be liable for any damage electronic parts. To avoid malfunctioning and caused by the customer. -
Page 7: Mounting
’ DFM1000 S MANUAL Wall mounting instructions 2.4 MOUNTING To ensure optimum reading capacity, estimate the scan distance of the scanner, Follow the next steps to make your scanner as described in this chapter. ready for installation in a system. Pay attention to the pitch and skew angles, 2.4.1. -
Page 8: Mounting Suggestions
’ DFM1000 S MANUAL 2.4.3. Mounting suggestions 2.5 POWER CONNECTION The DFM1000 can be placed on a flat surface or can be permanently mounted (fixed). The bottom of the scanner is provided with 2 slots with adjustable bolts and nuts for mounting Exercise caution at all times when on e.g. -
Page 9: Power Supply And Connection To The Host
’ DFM1000 S MANUAL For configuration of the DFM100 an additional Connect the scanner to the host. configuration kit is available. You are strictly Connect power supply to the scanner recommended to use this kit for optimaliza- (9-33V DC unregulated + 5%) tion. -
Page 10: Operation Of The Terminal
3.2 CHARACTERISTICS The DFM1000 is equipped with different char- acteristics. Some characteristics are already preset by Opticon and have a function. A num- ber of characteristics can be enabled or dis- abled by the user through configuration soft- ware and the configuration cable. In this chap-... -
Page 11: Check Mode
’ DFM1000 S MANUAL 3.2.4. Check mode 3.2.9. Bar code polarity To ensure the bar code is correctly decoded, The laser scanner is able to red positive and there are 2 options, to be enabled by the user. negative labels, for both black or coloured labels. -
Page 12: Working With The Scanner
’ DFM1000 S MANUAL WORKING WITH THE SCANNER 4.1 Scan Position Take care of the handling precautions. The bar code label of the product should be visible in the field of the scanner pattern. Make sure that the scanner is installed When the scanner is not able to decode the according to the installation bar code label of the product, it is possible to... -
Page 13: Pin Out
’ DFM1000 S MANUAL PIN-OUT COLOR FUNCTION BROWN The pinout description mentioned in this chap- ter must be used to connect the DFM1000 ORANGE scanner to the host. PINK PIN 1 - 4 : RS485 INTERFACE YELLOW not connected The pinout of the DB25 male connector is NOT compatible with GREEN standards for RS232. -
Page 14: Specifications
’ DFM1000 S MANUAL 6.3 Supported symbologies Codabar incl. ABC, CX Code 39 Code 93 (version DCCV0111 or higher) Code 128 EAN 8 incl. +2,+5 EAN 13 incl. +2,+5 IATA Industrial 2of5 SPECIFICATIONS Interleaved 2of5 ISBN ISSN Laetus 6.1 Electrical specifications Matrix 2of5 Italian Pharmaceutical Voltage requirement 9-33V DC unregulated,... -
Page 15: Environmental Specifications
’ DFM1000 S MANUAL 6.5 Environmental specifications 0 - 50 o C in operation Temperature -20 - 60 o C in storage Humidity 5 - 95 % in operation (non condensing) 5 - 95 % in storage Emission According to EN50081, part 1 &... -
Page 16: Troubleshooting
In this Scanner window is dirty. instance, please contact your dealer or Clean window with clean damp flintfree Opticon. cloth. Do not use abrassive liquids. When the terminal needs to be repaired, please ensure that the label with the serial Autotrigger does not react very well. - Page 17 ’ DFM1000 S MANUAL Scanner seems to work but the bar code can not be read. The bar code symbology to be read is disabled. Enable the bar code symbology in the software. Of a certain bar code symbology, some bar codes can be read while other can not be read.
-
Page 18: Product Ordering Information
’ DFM1000 S MANUAL PRODUCT ORDERING INFORMATION Article Code Scanner DFM-1000 laser scanner A15013R0010 including DB25 male connector + 1,5 m cable Additional Configuration kit for DFM A83200N0010 including configuration disc with configuration software RS232 adapter RS232 DB9 cable 12V power supply... -
Page 19: Test Labels
’ DFM1000 S MANUAL UPC A [default] 0 071589 812308 TEST EAN 13 [default] LABELS ( ISBN) Default labels 9 780123 456786 > In the default mode the scanner will only read the UPC and EAN labels ( 0123456789 ) without add-on. - Page 20 Industrial 2 of 5 (without CD) 0123456789 Interleaved 2 of 5 (with CD) with bearer bars 0123456784 Telepen ASCII ( Telepen numeric ) Telepen ( 57748174857483 ) Code 128 Code C ( EAN 128 ) 0123456789 ( ]C10123456789 ) Opticon Article Code O0225000010...
Need help?
Do you have a question about the DFM 1000 and is the answer not in the manual?
Questions and answers