Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Installation Manual
SERIES
KEYLESS ENTRY ALARM UPGRADE MODULE
Table Of Content
Arming Your System
Protection When Armed
Disarming Your System
Intrusion Warning Signals
Operating Panic From The Transmitter
Using Your Valet Switch
Custom Code Operation
Programming Custom Code
Additional Remote Features
Optional Ignition Control Auto Lock/Unlock
Eliminating Arm / Disarm Chirps
System Functions At A Glance
PATENTED: www.voxxintl.com/company/patents
Model PRO 9233E
OWNER'S MANUAL
Page 2
Page 3
Page 3
Page 3 - 4
Page 4
Page 4 - 5
Page 5
Page 6
Page 7
Page 7
Page 7
Page 8
128-9323
1 of 8
Advertisement
Table of Contents
Related Manuals for PURSUIT PRO 9233E
Summary of Contents for PURSUIT PRO 9233E
- Page 1 Model PRO 9233E OWNER’S MANUAL SERIES KEYLESS ENTRY ALARM UPGRADE MODULE Table Of Content Arming Your System Page 2 Protection When Armed Page 3 Disarming Your System Page 3 Intrusion Warning Signals Page 3 - 4 Operating Panic From The Transmitter...
- Page 2 Congratulations on your purchase of this automotive Keyless Entry Upgrade Alarm System. This system is a state-of-the-art auto security system that is designed to automatically arm and disarm when it receives a command from your existing Factory Keyless Entry Transmitter. Taking a few moments to read this manual will help to ensure that your vehicle is protected at all times.
- Page 3 IMPORTANT! When the system is programmed for passive arming, the system will always arm, even when the keychain transmitter has not been used to lock the doors. When you leave the vehicle, and a door has been left opened, the system will arm after 10 minutes.
- Page 4 1. I f the LED is flashing one time...pause...one time...pause...etc., then an intrusion attempt was made to a voltage sensing, light activated entry point, or to an optional sensor that has been connected to zone 1. 2. I f the LED is flashing two times...pause...two times...pause...etc., then an intrusion attempt was made to the hood or trunk, or to an optional sensor that has been connected to zone 3. I f the LED is flashing three times...pause...three times...pause...etc., then an intrusion attempt was made through one of the vehicle’s doors.
- Page 5 1. Open the vehicle door. The alarm will sound. 2. Turn the ignition key to the on position. 3. Within 5 seconds, press and hold the valet pushbutton switch. The alarm system will stop sounding and enter the (bypassed) mode. You can now start and operate the vehicle normally.
- Page 6 Programming Your Custom Override Code: Unlike override switches easily found, and defeated, this system allows the consumer to program a personal override code, offering a higher level of security. The system comes from the factory with a pre-programmed override code of 11. To change this default override code, do the following: 1.
- Page 7 You will note the LED flashing five times, pause, and then flash two times, pause. This pattern will be repeated three times indicating the new code (52) has been accepted and stored in memory. NOTE: If after step 7, the LED flashes a code other than what was just entered, this indicates that the code has not been changed. You will have to repeat steps 1 through 7 above being certain to note the following: Acceptable digits 10ths or units are 1 through 9.
- Page 8 PRO 9233E SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING ............PASSIVE ARMING SLOW FLASHING ................ARMED OFF ................... DISARMED ON - SOLID ................VALET MODE 3 FLASH ... PAUSE ............. INTRUSION ZONE 3 2 FLASH ... PAUSE ............. INTRUSION ZONE 2 1 FLASH ... PAUSE ............. INTRUSION ZONE 1 CHIRP INDICATORS 1 CHIRP * .................... 2 CHIRPS* ..................DISARM 3 CHIRPS ..............
Need help?
Do you have a question about the PRO 9233E and is the answer not in the manual?
Questions and answers