Page 2
NEC is a registered trade mark of NEC Corporation. All other registered trade marks are registered companys' property. ZEBEX is a registered trade mark of ZEBEX INDUSTRIES INC. All rights reserved, reproduction of this document or any portion of its contents is not allowed without the specific written consent of ZEBEX INDUSTRIES INC.
Page 3
IMPORTANT NOTICE USER'S MANUAL Every effort is made to ensure the accuracy of our product information; however, we accept no responsibility for errors or omission. Specification or version may be subject to change without notice. The actual specification and version are based on the product delivered.
TABLE OF CONTENTS Introduction ............1 Default Parameters.........2 Program Procedure ........5 System Setting ..........6 Header And Trailer .........7 Inter- Message Delay........7 Inter- Character Delay ........7 Message/ Block Mode Selection .....8 Beeper Tone Selection ........8 Bar Code ID Selection ........9 RS- 232C Serial Communication Parameters Setting ............10 Handshaking...
1. INTRODUCTION The series Bar Code Wand scanners can be configured by scanning a series of programming bar code labels. This allows decoding options and interface protocols to be tailored to a specific application. The configuration is stored in non- volatile memory and will not be lost by removing power from the scanner.
3. DEFAULT PARAMETERS DEFAULT VALUES OF KEYBOARD EMULATION PARAMETERS SETTING This table gives the default settings of all the programmable parameters. The default settings will be restored whenever the "Reset" programming label scanned scanner Function Default Values programming mode. Keyboard type selection IBM PC/AT USA Message terminator Enter/ Carriage...
HEADER AND TRAILER Start of Configuration • The reading of the "RESET " label turns all the Header parameters back to default values. • When you intend to turn your scanner back to default parameter, please scan the "Start of Trailer configuration"...
Start of Configuration Disable MESSAGE/BLOCK MODE SELECTION BAR CODE IDENTIFIER CODE SELECTION Enable Message Disable Block SEND COMMAND IN BLOCK MODE BAR CODE IDENTIFIER CODE SETTING COMMUNICATION UPC- E Enable UPC- A Disable EAN- 13 Store EAN- 8 SLZ 2 OF 5 GOOD READ BEEPER TONE SELECTION ITF 2 OF 5 2KHz/ 120 mSec...
Start of Configuration Hor. Tab STOP BIT STX/ ETX KEYBOARD EMULATION PARAMETERS SETTING KEYBOARD TYPE SELECTION PARITY IBM AT Even PS/ 2 55 IBM 5550 Mark (None) IBM 5295 Terminal Space IBM XT MESSAGE TERMINATOR (FOR RS-232C TYPE ONLY) IBM 3477/ 3472 Terminal IBM 5530-SC None...
MESSAGE TERMINATOR (FOR KEYBOARD WEDGE USE) Start of Configuration KEYBOARD TYPE SELECTION (Cont' d ¡ ^ None IBM 3196 Terminal Return ¡ ° ) APPLE MAC II Hor. TAB READING CODE SELECTION PS2/ 30 Note: The configuration of the items with asterisk ( ¡...
Start of Configuration IATA Disable READING CODE SELECTION (Cont' d) Italian Pharmac Enable ITF 2 of 5 Enable Italian Pharmac Disable CODE 39 PARAMETERS SETTING ITF 2 of 5 Disable CHARACTER SET SLZ 2 of 5 Enable Standard Code 39 SLZ 2 of 5 Disable Full ASCII Code 39 START/STOP CHARACTER TRANSMISSION...
CHECK DIGIT Start of Configuration INTERLEAVED 2 OF 5 PARAMETERS SETTING LENTGTH Calculate and Transmit Variable Calculate but not Transmit Fixed UPC/ EAN/ JAN PARAMETERS SETTING FORMAT CHECK DIGIT EAN-8 and EAN-13 UPC-A and EAN-13 Calculate and Transmit UPC-A and UPC-E Calculate but not Transmit UPC-A SLZ 2 OF 5 PARAMETERS SETTING...
Page 15
TRANSMIT UPC-A LEADING CHARACTER Start of Configuration UPC/ EAN/ JAN PARAMETERS SETTING(Cont' d) ADDENDUM TRANSMIT UPC-A CHECK DIGIT 5 Characters 2 Characters TRANSMIT UPC-E LEADING CHARACTER 2 or 5 Characters FORCE UPC-E TO UPC-A FORMAT TRANSMIT UPC-E CHECK DIGIT FORCE UPC-A TO EAN-13 FORMAT End of Configuration...