Related Manuals for Zebex Z-3392
Summary of Contents for Zebex Z-3392
- Page 1 Z-3392 Handheld Gun Type 2D Image Reader Service Guide Revision History Changes to the original manual are listed below: Version Date Description of Version Nov. 21, 2016 Initial release...
-
Page 2: Preface
This manual is in A4 format. Please check your printer setting before printing it out. Disclaimer Please seek professional help if you are not confident/competent at performing any of the procedures in this guide. Zebex will accept no responsibility for any loss, damage or injury that may occur. Z-3392 Service Guide 2 / 12... -
Page 3: Table Of Contents
Important Notice ..................................2 Radio Notice...................................2 For CE-Countries ...................................2 Disclaimer ....................................2 Table of Contents................................3 Introduction ..........................錯誤! 尚未定義書籤。 Product Overview..........................錯誤! 尚未定義書籤。 Scanner Parts ..................................4 Take Apart ..................................6 Before You Start ..............................6 Important Instructions ..............................6 Tools to Prepare ..................................6 Z-3392 Service Guide 3 / 12... -
Page 4: Scanner Parts
ERVICE UIDE Scanner Parts The scanner includes the following parts: Z-3392 Service Guide 4 / 12... - Page 5 ERVICE UIDE Name Quantity 560-433920-003 Z-3392 handle top cover 560-433920-004 Z-3392 handle base 689-100000-026 Z-3392 LED light guide panel-indicator 689-100000-027 Z-3392 LED light guide panel-decoding 662-203392-001 Z-3392 LED bracket 603-033920-003 Z-3392 dust cover rubber 684-100000-028 Z-3392 dust cover - 1082...
-
Page 6: Take Apart
• Follow all instructions. • Heed all warnings. Tools to Prepare • Philips screwdriver. Please follow these steps to take apart Z-3392. Remove the screws （521-01E000-010*2）from the scanner. Remove the screws （521-01E000-010*2）from the scanner. Z-3392 Service Guide 6 / 12... - Page 7 ERVICE UIDE Remove the screws （521-013000-5R0 *8）from the scanner. Remove the light guide panels and the LED cover. Remove the FFC 8Pin cable. Z-3392 Service Guide 7 / 12...
- Page 8 ERVICE UIDE Remove the screws （521-013000-5R0 *2）. Separate the LED board. Remove the screws （521-013000-010 *4）. Z-3392 Service Guide 8 / 12...
- Page 9 Remove the LED bracket and separate the dust cover and dust cover rubber. 10. Remove the Mylar tape and remove the 16Pin FFC cable. 11. Remove the screws （521-013000-5R0 *2）and remove the main board assembly and sound guide. Z-3392 Service Guide 9 / 12...
- Page 10 ERVICE UIDE 12. Remove the 24Pin FFC cable. 13. Remove the speaker net. 14. Remove the screws （521-00E000-600 *2）. Z-3392 Service Guide 10 / 12...
- Page 11 ERVICE UIDE 15. Remove the handle base assembly and the trigger. 16. Remove the screws （520-0140R5-6R0 *1）. 17. Separate the cable base cover from the scanner base. Z-3392 Service Guide 11 / 12...
- Page 12 ERVICE UIDE 18. Remove the screws （521-013000-5R0*2）;peel off the Mylar tape and remove the 16Pin FFC cable. 19. Separate the trigger support and trigger sealing rubber from IO board assembly. Z-3392 Service Guide 12 / 12...