Advertisement

STATEMENT OF LIMITED WARRANTY
MÁQUINAS AGRÍCOLAS JACTO S.A. shall warrant the equipment described in
this manual and shall repair or replace parts and components which, under normal operation
and wear, in accordance with technical recommendations, show DEFECTS IN MATERIAL
OR WORKMANSHIP, based on the following conditions.
WARRANTY PERIOD
- 01 (one) year from the date of sale to the original purchaser.
WARRANTY APPLICATION
- JACTO shall honour this warranty, free of charge, if any part or component shows defect
in MATERIAL OR WORKMANSHIP, after final analysis at the factory.
THIS WARRANTY SHALL BE NULL & VOID IN CASE OF:
- Misuse of the equipment against specifications in the OPERATOR'S MANUAL, overwork
or accidents.
- Preventive/remedial maintenance performed by unauthorized people.
- Use of parts and components not supplied by JACTO.
- Modification of the equipment or any characteristic of the original design.
THIS WARRANTY SHALL EXCLUDE:
- Parts which show wear and tear due to use, UNLESS THEY SHOW DEFECTS IN
WORKMANSHIP, ASSEMBLY OR MATERIAL.
- Damages resulting from accidents.
- Transportation or freight of the equipment, parts and components in case such warranty
is not approved.
- Transportation and mobilization of technicians.
GENERAL INFORMATION:
- Parts replaced within the warranty period shall be property of JACTO.
- The warranty on replaced parts and components shall expire together with the equipment
warranty period.
- Eventual delays in performing services shall not give the owner right either to indemnity
or to extension of the warranty period.
- JACTO reserves the right to modify its products or to interrupt the manufacture without prior notice.
M Á Q U I N A S A G R Í C O L A S J A C T O S . A .
Rua Dr. Luiz Miranda, 1650
17580-000 - Pompéia - SP - Brasil
Tel.: +55 14 3405-2100 - Fax: +55 14 3452-1306
E-mail: export@jacto.com.br
Home page: www.jacto.com.br
01/2006 - 131607 - 0005-MI
OPERATOR'S MANUAL
X-15
1- INTRODUCTION
This manual contains information for the proper assembly, operation and care of your
sprayer.
Carefully read and follow the instructions contained in this manual before using your
sprayer.
2- SPRAYER VIEW
Chamber
Lever
Tank
Nozzle
3- SPECIFICATIONS
Model ......................... X-15
Net weight .................. 4.6 kg
Tank
- Capacity ................... 15 liters
- Material .................... Polyethylene (plastic)
- Fill opening diameter . 115 mm
Diaphragm
Lid
Trigger
valve
Lance
Pump
- Type ........................................ Piston
- Material .................................... Polyamide
- Working pressure (max.) .......... 6 kgf/cm²
Lance length .............................. 600 mm
Hose length ............................... 1650 mm
Nozzle fitted .............................. JD-12P

Advertisement

Table of Contents
loading

Summary of Contents for Jacto X-15

  • Page 1 - Eventual delays in performing services shall not give the owner right either to indemnity or to extension of the warranty period. - JACTO reserves the right to modify its products or to interrupt the manufacture without prior notice. 3- SPECIFICATIONS Model ......
  • Page 2: Assembly Procedures

    Description Item Description Item Part no. Part no. Take out of the sprayer carton the following parts. X-15 33 427062 Nozzle assembly 01 214486 Pumpin rod assembly (includes: ref. 45,46 47) Tank 02 925800 Lance holders set 34 996058 Trigger valve cap...
  • Page 3: Parts List

    PARTS LIST 6- INSTALLING THE LANCE HOLDERS 60mm - Secure the lance holders to the rod as shown below. Screw 300mm Holders 7- ATTACHING THE LANCE TO THE TRIGGER VALVE - Push the lance into the trigger valve and secure it with the screw cap. Elbow Screw cap Lance...
  • Page 4: Adjusting The Strap

    Antidrip valve, attachable to wand of knapsack sprayers. Mounted with JD-12P nozzle. Handle 834382 X-15 basic repair kit. It contains: piston cup, diaphragm, trigger valve cap and needle assembly. 838052 VPC (1 and 2 kgf/cm²) - Ensures constant pressure. Non-drip...
  • Page 5 13- MAINTENANCE - Take the container cap off and carefully pour the rinse water into CLEANING THE SPRAYER - After finishing the spray application, clean and wash all equipment in an approved the spray tank. decontamination area. - Keep holding the container over the spray tank opening ATTENTION: Pump for approximately 30 seconds to the last drop.
  • Page 6: Troubleshooting

    TRIPLE WASH OF EMPTY AGROCHEMICALS CONTAINERS 15- TROUBLESHOOTING - Put about 2 liters of water in the tank. Even the containers considered empty contain chemical residues. - While operating the lever, look into the tank to see how the problem arises. Some publications show that somewhere around 0.3% of the chemicals remains in the - Refer to the table and diagram below.
  • Page 7: Calibration Of Manual Knapsack Sprayer

    - Do not eat, drink or smoke while spraying. - Do not pollute the environment. CALIBRATION OF MANUAL KNAPSACK SPRAYER PROCEDURE USING CALIBRATOR BOTTLE (OPTIONAL) - Hold the lance at the working height and spray to measure the application band width. - Based on the band width, calculate the total walking distance required to spray the desired area.
  • Page 8: Spray Nozzles

    SPRAY NOZZLES SAFETY PRECAUTIONS NOZZLE IDENTIFICATION PRESSURE FLOW RATE APPLICATION TYPE (Part no. - Description) (psi) (ml/min) Flat fan 454215 - 80EF015 ATTENTION! Kematal (Green) READ CAREFULLY 454223 - 80EF02 Herbicides Kematal (Yellow) THE CHEMICALS 454231- 80EF03 1,250 MANUFACTURER'S Kematal (Blue) Cone LABELS 717942 - JD-10A...

Table of Contents