Table of Contents
Advertisement
1.STANDARD EQUIPMENT AND SPECIFICATIONS
ROTARY GRASS MOWER
Width of Cut:
60"
Blade Bar:
Single leaf, 5"x7/8"
Blade:
14"x3"x 1/2", free-swinging
Hyd. Motor Rating:
Gear type, 74 HP (at 2500 PSI
Deck Thickness:
14-gauge
Side Skirts:
1/4" thick
Frame:
3/8" bar. cross-braced
Skid Shoes:
Full-length, replaceable
Debris Deflector:
3-ply rubber belting, front & rear
FLAIL-AXE
®
Width of Cut:
48"
Cutter Shaft:
4-1/2" dia. steel tube, 3/8" wall,
greased bearings
Knives:
16 ea., 2 pound, 360 deg. swing,
reversible
Hyd. Motor Rating: Gear Type, 76 HP (a) 3000 PSI @ 2400 RPM
Deck Thickness:10-gauge
End Plates:
3/8"
Deck Frame:
4" square cross-tube
Skid Shoes:
Full-length, replaceable
Rear Roller:
5-1/2" dia. tube, adj. 3/4" to 6"
Debris Deflector: Full-width rubber-covered fabric, rear.
Removable full-width steel, front.
BUZZBAR
TREE LIMB CUTTER
®
Cutting Width:
7-1/2"
Blades:
Four blades, each 26" in diameter
and 3/16" thick
Cuts up to 4" diameter tree limbs
Hydraulic Motor:
38 HP
Main Channel:
Formed of 3/16" sheet steel
End Plates:
3/8"
Roller Bearings:
Tapered with factory set pre-load
Rear Shield:
10-gauge steel formed for stiffness
TIMBER CAT
SICKLE BAR
®
Cuts up to 4" tree limbs
Width of Cut:
Blade Bar:
5/8" thick
Blade:
T-l steel
Direct coupled operating hydraulic cylinder
{excludes pitman).
The Mower is designed for certain mowing applications and is rated to cut up to a specific
size vegetation (see Mower Standard Equipment and Specifications). DO NOT use this
mower to cut vegetation above the Mower's rated capacity or to cut any type of non-
vegetative material. Only operate this Mower on a properly sized and equipped Tractor.
Operating this Mower in an application for which it is not designed and/or operating the
Mower with the wrong size Tractor can cause Mower component damage and equipment
failure resulting in possible serious injury or death.
A-BOOM 02/10
©2010 Alamo Group Inc.
OPERATION
5' or 7'
Operation Section 3-3
HEAVY DUTY GRASS FLAIL
Width of Cut:
48" or 60"
Cuttershaft:
4-1/2"
bearings
Knives:
36 pair of 3 o/. knives are standard
Hyd. Motor Rating:
Gear Type 76 HP @ 3000 PSI @
2400 RPM
Deck Thickness:
10- gauge
End Plates:
1/4" thick
Deck Frame:
2-7/8" tube, full-width front & rear
Skid Shoes:
Full-length, replaceable
Rear Roller:
6" tube greaseable bearings
Debris Deflector:
Full-width, rubber -covered fabric,
rear
BOOM-AXE*
Widths of Cut:
60" std., 50" opt.
Blade Bar:
60"-3 leaf 5"x 7/8"(up to 6 blades.)
50"-3/4" x 29" disc.(up to 6 blades.)
Blades:
60"-5"xl4"x5/8"replaceable.
Hyd. Motor Rating:
Gear Type 101 HP @
2750 PSI @ 2400 RPM
Deck Thickness:
10 gauge
Side Skirts:
3/8"
Frame:
Cross-braced. 3/8" bar
Skid Shoes:
Replaceable, full-length
Debris Deflector: Front, spring-loaded, retractable shield.
Rear, 3-ply rubber belting.
OPTION
50" cutting head. Avo-leaf blade bar with two blades.
DITCHER
Cutting Width:
22" rotor
Blade Carrier:
1/2" disc with gusset backing
Blade:
9" x 5-1/2" reversible
Hyd. Motor Rating:
Gear Type 172 HP (a; 2500 PSI
Bonnet (deck):
3/8"
Frame:
6" x 1 0" tube
Wear Plates:
2-1/2" x4"x 3/8" replaceable, 3 ca.
Debris Deflector:
Adj. 90 deg. down to horizontal
OPTION
Reverse head to deposit spoil on tractor side of ditch.
SICKLE
BAR MOWER
Width of Cut:
5'
Cutterbar: Knives:
6" tapered x 5/8"
Knives:
20 ea. 3" triangular sections
Hyd. Motor Rating:
35 HP @ 700 RPM
Rock Guards:
19 ea. with replaceable
Skid Shoes:
ledger plates 1 4". replaceable
Knife Speed Control:
Hyd. Governor
Drive Connection:
Pitman lcss
(SGM-14)
balanced
tube,
greased
Advertisement
Table of Contents
