Page 1
1.109-664.0 5832SS 1.109-651.0 5835SS 1.109-652.0 5836SS 1.109-653.0 For the Hotsy Dealer nearest you, consult our web page at WARNING: www.hotsy.com This product and accessories may contain a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.
If the pressure washer demonstrates other symptoms or the corrective actions listed do not correct the problem, contact the local authorized Hotsy Service Center. The Hotsy Service Center can be identified by visiting www.hotsy.com. When ordering from your dealer, please provide the following:...
Model: Date of Purchase: Serial Number: Dealer: Address: Phone Number: Sales Representative: The model and serial number of your machine is located on the back of the machine. MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
When ordering parts, please specify model and serial number. Use only identical replacement parts.This machine is to be used only by trained operators MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
à l'écart de RISK OF KEEP WATER ASPHYXIATION. tout câblage électrique ou des SPRAY AWAY FROM USE THIS PRODUCT chocs électriques mortels ELECTRICAL WIRING. ONLY IN A WELL VENTILATED AREA. pourraient survenir. MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
Page 7
To reduce the risk of injury, close supervision is necessary when a machine is used near children. Do not allow children to operate the pressure washer. This machine must be attended during operation. MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
Page 8
à cette fin ou devraient se situer à 45 cm (18 po) ou plus au-dessus du sol. Installer un sol non combustible et fournir un espace de travail d'au moins 90 cm (36 po). MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
10. Do not store LP-gas containers indoors or in enclosed areas. Do not expose LP-gas container to heat. Always store with service valve closed and plugged as required. MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
Page 11
L 51” X W 31” X H 54” 5835SS 1275 Lbs 12” L 51” X W 31” X H 54” 21 Amps 1035 Lbs 5836SS 16 Amps 1035 Lbs 1275 Lbs 12” L 51” X W 31” X H 54” MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
(Not Included) Pressure Hose, Trigger Gun and Wand 1. When assembling, use teflon tape on all plumbing connections to prevent leakage. 2. Install the pressure hose on the pressure washer as shown. Pressure Hose MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
Local code will require certain distances from floor and walls. WARNING: Avoid small areas or near exhaust fans. AVERTISSEMENT: Éviter les petites superficies ou les surfaces à proximité des ventilateurs d'extraction MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
525,000 BTU/HR at the machines rated manifold pressure. Consult building codes for installation requirements. For proper and safe machine operation, we recommend that a licensed contractor be consulted for machine installation. MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
— not matches. pipe; fittings further reduce capacity. For example, in 1" size, an elbow is equivalent to about 2.6 feet of pipe and a tee is equivalent to about 5.2 feet of pipe. MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
Propane tanks present a real danger in the waste Hotsy natural and LP gas series pressure washers that stream, so it is essential to properly dispose of old incorporate a natural draft burner assembly designed to tanks so they do not injure you or sanitation workers.
Uniform Building Code. ated dampeners. Hotsy is not a licensed contractor and as such we are unable to make recommendations for suitable Vents penetrating ceilings or walls should be double- make and model of power vents.
Sampling Port A port for sampling flue gases and supply piping system or damage to the gas valve will measuring the flue gas temperature should be placed occur. 18” above the flue collar. The port should be covered MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
Page 20
Most or all of the lost outlet temperature can be recovered by installing and adjusting a damper in the stack. However this adjustment must only be performed by a trained MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
Page 21
Au Canada, la conversion au gaz doit être effectuée conformément aux exigences des autorités provinciales compétentes et conformément aux exigences du code d'installation CAN/GGA-B149.1 et .2. MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
12. Dials must only be operated by hand. Never use pliers, wrenches or other tools to turn dials. 13. Leak test with a soap solution after installation or service with the main burner on. Coat pipe and tubing joints, gaskets, etc. MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
Have gas lines been checked with local codes? Have all operators using this machine been instructed properly and have they read the manual? Has the machine been installed according to operator's manual instructions? MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
Ammoniac ou produits à base d'acide non approuvées peut causer des lésions corporelles et/ou des dommages à la propriété, et annulera la These chemicals will harm the machine and will damage garantie du fabricant. the surface being cleaned. MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
NOTE: This valve must be inspected and tested • Use only high quality detergents and follow man- annually by a certified Hotsy technician. ufacturer’s mix recommendations. Unloader Valve • Flush the system with clear water immediately after using detergent solutions.
Inadequate fuel supply Check fuel supply. NOT PRODUCE HOT WATER Pump switch turned off Pump must be running before burner will light. BURNER SMOKES OR HAS OBNOXIOUS Stack restriction See Venting under Installation. ODOR MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
Page 28
4. If you do not have continuity through wire and the ignitor/sensor, check for a loose wire connection in the wire. Repair as needed. 5. Check to see if spark shorts to burner ring through a cut in the ignitor wire. MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
Page 29
If you read 24V across the switch terminals the limit switch is open. Replace the limit switch. A pilot flame set too high will also cause burner to short cycle. Pilot flame lifts over ignitor/sensor. MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP 9.808-037.0-A...
Page 30
If you need SERVICE on your pressure washer, contact your local Hotsy dealer or visit www.Hotsy.com. Smart phone users scan the code below to link directly to the Service Request page. To REGISTER your pressure washer, please visit our Warranty Registration page at www.hotsy.com/WarrantyRegistration.aspx or scan the code...