Subscribe to Our Youtube Channel
Related Manuals for ParaBody 897104
Summary of Contents for ParaBody 897104
-
Page 1: Assembly Instructions
897104 WEIGHT STACK OPTION ASSEMBLY INSTRUCTIONS Part # 6819801 Revision: 2/17/99... -
Page 2: Tools Required For Assembly
WELCOME TO THE WORLD OF Please note: * Thank you for purchasing the Parabody 897104 WEIGHT STACK OPTION. Please read these instructions thoroughly and keep them for future reference. This product must be as- sembled on a flat, level surface to assure its proper function. -
Page 3: Parts List
PART # DESCRIPTION 6xxxx STACK BASE 6819403 STACK BOOM 6819703 1-3/4” X 9-3/8” TUBE 6577801 77-1/4” GUIDE ROD 6284501 20 HOLE WEIGHT STACK SHAFT 3116201 3-1/2” PULLEY 6660101 129-1/2” CABLE 6692601 3 X 2” END CAP 3103302 13/16” SHAFT COLLAR 6214401 WEIGHT STACK SELECTOR PIN 6236701... - Page 4 FIGURE 2 STEP 2: • LOOSEN the TOP BOOM from the UPRIGHT FRAME by removing one 1/2 X 2-1/2” BOLT, one 1/2 X 3” BOLT, one 3/8 X 2-3/4” BOLT, two 1/2” WASHERS, one 1/2” LOCK NUT, and one 3/8” LOCK NUT as shown in FIGURE 2. •...
- Page 5 FIGURE 4 STEP 4: • Insert two 3 X 2” END CAPS (8) into the ends of the STACK BOOM (2) as shown in FIGURE 4. • Insert two GUIDE ROD BUSHINGS (22) into the tubes on the STACK BOOM (2) as shown in FIGURE 4. •...
- Page 6 UPRIGHT FRAME 18 1/2 X 3-1/4” FIGURE 6 STEP 6: • SECURELY assemble the STACK BASE (1) to the bottom of the UPRIGHT FRAME using one1/2 X 3-1/4” BOLT (18) and one 1/2” LOCK NUT (20) as shown in FIGURE 6. FIGURE 7 STEP 7: •...
- Page 7 3/8 X 1-1/4” 12 FIGURE 8 STEP 8: • Insert two GUIDE RODS (4) into the STACK BASE (1) as shown in FIGURE 8. Lubricate the GUIDE RODS (4) with a slicon or teflon spray that is available at most hardware stores. •...
- Page 8 FIGURE 9 STEP 9: • Slide the STACK BOOM (2) over the GUIDE RODS (4) and inside the tube on the UPRIGHT FRAME as shown in FIGURE 9. FIGURE 10 STEP 10: • LOOSLY assemble the TOP BOOM to the UPRIGHT FRAME using the previously removed 1/2 X 2-1/2” BOLT, one 1/2 X 3” BOLT,one 3/8 X 2-3/4”...
- Page 9 FIGURE 11 STEP 11: • Route the 129-1/2” CABLE (7) through the TOP BOOM and the STACK BOOM (2) as shown in FIGURE 11. • TIGHTEN any LOOSENED PULLEY connection after CABLE has been routed. FIGURE 12 3/8 X 2-3/4” 13 STEP 12: •...
- Page 10 CABLE accordingly and retighten the jam nut. Thank you for purchasing the Parabody 897104 WEIGHT STACK OPTION. If unsure of proper use of equip- ment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
Need help?
Do you have a question about the 897104 and is the answer not in the manual?
Questions and answers