Advertisement
Quick Links
Advertisement
Related Manuals for ParaBody 841101
Summary of Contents for ParaBody 841101
- Page 1 Serious Steel 841101 WEIGHT STACK OPTION ASSEMBLY INSTRUCTIONS Part # 6754401 Revision:12/16/97...
-
Page 2: Important Notes
2. Do not allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. -
Page 3: Parts List
PART# DESCRIPTION 6745003 UPRIGHT 6753703 TOP BOOM 6274402 LOW ROW BAR 6275302 LAT BAR 6609002 LOW ROW ATTACHMENT 6610402 KNEE SUPPORT 6750503 WEIGHT STACK BASE 6176201 ROLLER PAD 6754501 79-1/2" GUIDE ROD 6189501 WEIGHT STACK LABEL 3116101 4-1/2" PULLEY 3116201 3-1/2"... - Page 4 FIGURE 2 STEP 2: ¯ Insert two 2" SQ ENDCAPS (36) Into the ends of the UPRIGHT (1) as shown in FIGURE ¯ SECURELY assemble the LOW ROW ATTACHMENT BOLTS (27), four 3/8" WASHERS (31), and two 3/8" LOCK NUTS (32). See FIGURE (5) and the UPRIGHT (1) to the POWER RACK using Vz¢o 3/8 X 3-1/4"...
- Page 5 ¯ SECURELY assemble the WEIGHT STACK BASE (7) to the UPRIGHT (1) using two 1/2 X 3" BOLTS (28), two 1/2" ERS (29), and two 1/2" LOCK NUTS (30) as shown in FIGURE STEP4 Insert two WEIGHT PLATE BUSHINGS (42) into the "PARABODY" side of each of the twenty WEIGHT PLATES (43) as shown in FIGURE FIGURE 4...
- Page 6 STEP 5: ¯ Insert four CAP PLUGS (21) into the bottom end & top end of the two GUIDE RODS (9) as shown in FIGURE ¯ Securely assemble the WEIGHT STACK SHAFT (13) to the HEAD PLATE (14) using one 3/8 X 1-1/4" BOLT (23) and one WASHER (31).
- Page 7 I FIGURE 6 STEP 6: ¯ Insert two 2 X 3" END CAPS (34) into the TOP BOOM (2) as shown in FIGURE Route threaded end of the LAT CABLE (15) through the TOP BOOM (2) as shown in FIGURE SECURELY assemble two 3-1/2"...
- Page 8 FIGURE 8 STEP 8: ¯ Route threaded end of the LAT CABLE (15) around the one of the PULLEYS in PLATE & PULLEY ASSEMBLY (17) through the holes in the TOP BOOM (2) as shown in FIGURE SECURELY assemble two 3-1/2" PULLEYS (12) to the TOP BOOM (2) using two 3/8 X 2-3/4" BOLTS (25), figur FLANGE SPACERS (33), and two 3/8"...
- Page 9 FIGURE 9 3"(~~ 3"~ STEP 9: ¯ Swing the GUIDE RODS (9) under the TOP BOOM (2) as shown on FIGURE ¯ Assemble the TOP BOOM (2) over the GUIDE RODS (9) and SECURELY assemble the TOP BOOM (2) to the UPRIGHT using two 1/2 X 3"...
- Page 10 2-3/4"~ STEP 10: Loop the ball end of the LOW ROW CABLE (16) aro " und one 3-1/2 PULLEY (12) and SECURELY assemble the 3-1/2" PUL- LEY (12) to the UPRIGHT (1) using two 3/8 X 2-3/4" BOLTS (25), two 3/8" FLANGE SPACERS (33), two 3/8" (31), and two 3/8"...
- Page 11 FIGURE 11 STEP 11: ¯ Route the threaded end of the LOW ROW CABLE (16) around the bottom PULLEY of the PULLEY & PLATE ASSEMBLY (17) as shown in FIGURE 11. STEP 12: Screw the threaded end of the LOW ROW CABLE (16) approximately 3/4"...
- Page 12 FIGURE 13 STEP 13: ¯ Attach the LAT BAR (4) to the ball end of the LAT CABLE (15) using one SNAP LINK (41) as shown in FIGURE ¯ Slide two 1 X 8" GRIPS (18) over the ends of the LAT BAR (4) as shown in FIGURE STEP 14: Attach the LOW ROW BAR (5) to the ball end of the LOW ROW CABLE (16) using two...
- Page 13 FIGURE 15 STEP 15: Slide two ROLLER PADS (8) onto the KNEE SUPPORT (6), then insert one 1-3/4" SQ. END CAP (37) into the end of the SUPPORT (6) as shown in FIGURE 15. FIGURE 16 STEP 16: When performing the LAT PULL exercise, insert the KNEE SUPPORT (6) into the hole of the SAFETY RAIL as shown in FIG- URE 16 and simply lower the SAFETY RAIL down until rollerpads contact knees.
- Page 14 L AT CABLE (15) and the LOW ROW CABLE (16) acco~rdingly retighten thejamnut. See FIGURE 17. ¯ Make sure all connections are tight and secure. THIS CONCLUDES THE ASSEMBLY OF THE 841101 up. See FIGURE 17. WEIGHT STACK OPTION...