Page 1
829 LEG CURL/EXTENSION WARNING: Read and follow all directions for each step to insure proper assembly of this product. USER’S GUIDE CLASS H PART # 7078201 REV. B Version: 829107 Revision: 06/26/01...
Please note: * Thank you for purchasing the ParaBody 829 LEG CURL/EXTENSION. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated.
PART # DESCRIPTION 6259108 FRONT SUPPORT TUBE 6625402 BACK PAD ADJUST TUBE 6625502 BACK PAD SUPPORT TUBE 6216702 1-3/4 SQ X 5" TUBE 6668202 1-3/4 SQ X 13-1/2" TUBE 6662002 LEG CURL/EXTENSION 6661221 BACK PAD ASSY 6661621 SEAT PAD ASSY 6662208 LEG EXT HANDLE RHT 6662308...
Page 6
STEP 1 Insert four PARABODY LOGO END CAPS (37) into the ends of REAR BASE LEG (12) and FRONT BASE SUPPORT (1). See FIGURE 1. STEP 2 Slide two 1-1/4 x 5” GRIPS (36) over tubes on REAR BASE LEG (12). See FIGURE STEP 3 Securely assemble REAR BASE LEG (12) to LEG FRAME (11) using two 3/8 X 3”...
Page 7
STEP 6 Securely assemble RIGHT (9) & LEFT (10) LEG EXT HANDLES to LEG FRAME (11) using two 3/8 X 4” BOLTS (21), four 3/8” FLAT WASHERS (24) , and two 3/8” LOW HEIGHT NYLOCK NUTS (27). See FIG- URE 5. STEP 7 Insert two 3 X 2”...
Page 8
STEP 10 Securely assemble BACK PAD ADJUST TUBE (2) & BACK PAD SUPPORT TUBE (3) to LEG FRAME (11) using one 1/2 X 7” BOLT (23) and one 1/2” LOW HEIGHT NYLOCK NUT (26). (NOTE: SECURELY TIGHTEN BOLT THEN BACK NUT OFF 1/4 TURN TO ALLOW THE TWO PARTS TO ROTATE FREELY.) See FIGURE 8.
Page 9
STEP 13 Slide two HINGE TABS (31) over posts on LEG FRAME (11). See FIGURE 11. STEP 14 Securely attach the SEAT PAD (8) to the HINGE TABS (31) using two 3/8 X 1” BOLTS (19) and two 3/8” FLAT WASH- ERS (24).
Page 10
STEP 16 Attach eight 1-1/2” X 3/4” GLIDES (33) to 5” ROLLER PAD ADJUSTER (4) and attach eight 1-1/2” X 3/4” GLIDES (33) to 13-1/2” ROLLER PAD ADJUSTER (5) as shown in FIGURE 14. STEP 17 Securely assemble two 3/8” SPRING PIN AS- SEMBLIES (17) into the spring pin barrels on the LEG CURL/EXTENSION (6) as shown in FIGURE 15.
Page 11
Attach four ROLLER PADS (15) to the LEG CURL/EXTENSION (6) using two 16” ROLLER PAD SHAFTS (13) and four STARLOCK COLLARS (35). See FIGURE 18. THIS CONCLUDES THE ASSEMBLY OF THE PARABODY 829 LEG CURL/EXTENSION 26 LOW HEIGHT FIGURE 17 FIGURE 18 22 1/2 X 4”...
YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION. REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND MAIL BACK. MODEL #________________________ SERIAL #_________________________ DATE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ Thank you for purchasing the ParaBody 829 LEG CURL/EXTENSION. MAINTENANCE...
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired or replaced by ParaBody.
Page 14
Life Fitness Italia S.R.L. Via Elvas 92 39042 Bressanone Italy Phone: 39 (472) 835-470 Fax: 39 (472) 833-150 Life Fitness Asia Pacific Limited Room 2610, Miramar Tower 132 Nathan Road, Tsimshatsui Kowloon, Hong Kong Phone: (852) 2891-6677 Fax: (852) 2575-6001 LIFE FITNESS www.parabody.com...