Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Simrad M5000 Series
Summary of Contents for Simrad M5000 Series
- Page 1 M5000 Series Monitors User Guide ENGLISH...
- Page 3 Wheelmark, which is a symbol of conformity with the Marine Equipment Directive. The M5000 Series (M5016, M5019 and M5024) monitors comply with IEC62388 Ed.1 for Radars. The monitors can be used as part of a radar system applying for type approval.
- Page 4 HDMI Licensing LLC in the United States and other countries About this manual This manual is a reference guide for installing and operating the Simrad M5000 Series monitors. Important text that requires special attention from the reader is emphasized as follows: ¼...
-
Page 5: Table Of Contents
Connecting power Operating the display First time operation OSD menu Cleaning and maintenance Display removal Replacing the gasket Replacing the filters Other maintenance Checking current firmware version Installing an update Troubleshooting Accessories Specifications Dimensional drawings Contents | M5000 Series User Manual... -
Page 6: Introduction
Introduction The Simrad M5000 series monitors offer a low profile, high brightness solution for displaying video from a variety of sources. This includes 3 models; M5016, M5019 and M5024. • The whole M5000 series range complies with IEC62388 for Radars. -
Page 7: Installation
Fixing options The M5000 series monitors can be dash or bracket mounted (using optional VESA adaptor). When dash mounting, unit should be fitted using the rear mounted dash mount brackets, and bezel screws from the front. Exclusion of the dash mount bracket will greatly increase strain on bezel screws and adjacent bezel plastics, and is not recommended. -
Page 8: Flush-Mounting The Display
ь ор ер ча в со ам и. ст и о и Drill cutout corners with a small pilot drill bit followed with 13 mm drill bit. Complete cutout with jigsaw or similar tool. Installation | M5000 Series User Manual... - Page 9 5 mm of threaded rod protrudes through other side of bracket. Fit stopper foot on to end of wing screw. Complete for both threaded holes on each bracket. Installation | M5000 Series User Manual...
- Page 10 Hand tighten wing nuts against the back of the mounting brackets to lock the wing screw in place. Hold wing screw stationary if it turns while adjusting the wingnut. 10 | Installation | M5000 Series User Manual...
-
Page 11: Vesa Mounting The Display
The bracket mounting points on the monitor are only intended to carry the weight of the monitor - do not install monitor in such a place where it may be used as a handhold, or have additional equipment attached to it. | 11 Installation | M5000 Series User Manual... -
Page 12: Connecting The Display
Connecting the display The M5000 series monitors largely use industry standard cables, which can be purchased pre-terminated in a variety of lengths. The following chapter provides additional detail where cables require field termination by the installer. Rear connections Connection Function... -
Page 13: Connecting Power
Chassis ground will typically not be required. In certain problematic installations it may help stabilize touch screen sensitivity, i.e. prevent ‘false’ touches, or non-registered touches. Recommended fuse rating Model M5016 M5019 M5024 Fuse 3 amp 4 amp 4 amp | 13 Connecting the display | M5000 Series User Manual... -
Page 14: Operating The Display
This auto adjustment will take place when the unit is first installed and connected to a source and there after, if the video input changes, or is user initiated. 14 | Operating the display | M5000 Series User Manual... -
Page 15: Osd Menu
Picture) Adjusts horizontal position, where 0 = left, and PIP Horizontal 0-100 100 = right Adjusts vertical position, where 0 = bottom, PIP Vertical 0-100 and 100 = top | 15 Operating the display | M5000 Series User Manual... - Page 16 12 V to yellow wire when figuration monitor is on Key Beeps Off, On Turns on or off the OSD key beeps Factory Reset Yes, No Restore all settings to default 16 | Operating the display | M5000 Series User Manual...
-
Page 17: Cleaning And Maintenance
The backing paper on outside of gasket will help prevent stretch, and should only be removed when display is ready to install in to dashboard. | 17 Cleaning and maintenance | M5000 Series User Manual... -
Page 18: Replacing The Filters
OSD version, BIOS version, and the serial number. Installing an update Updates should be loaded via a compatible Simrad device such as the NSO evo2. Refer to the applicable product manual on how to upgrade a device over NMEA 2000. -
Page 19: Troubleshooting
Video compromised by interference from other equipment Vertical shaded bars on Incoming video may be in 4:3 ratio, either leave in ‘aspect’ mode, screen image or set to ‘fill’ to use full screen space. | 19 Troubleshooting | M5000 Series User Manual... -
Page 20: Accessories
M5016/19/24 inlet filter cover 000-11624-001 HDMI cable (3 m) 000-11248-001 HDMI cable (10 m) 000-11249-001 Connector kit (power and serial plugs) 000-11625-001 ¼ Note: Occasionally available accessories may change - refer to the website: http://pro.simrad-yachting.com/. 20 | Accessories | M5000 Series User Manual... -
Page 21: Specifications
(8-32 bit colour, 60 Hz) Hz Interlaced) 1024 x 768 (8-32 bit colour, 60 Hz) ¼ Note: Occasionally specifications may change - refer to the latest edition of the manual on the website: https:pro-simrad-yachting.com. | 21 Specifications | M5000 Series User Manual... -
Page 22: Dimensional Drawings
Dimensional drawings M5016: 383mm M5019: 461mm M5024: 598mm MAX 25.4 mm (1.00") M5016: 400mm M5019: 478mm M5024: 625mm 8 mm (0.31") 66.0 mm (2.60") MAX 88.0 mm (3.46") 22 | Dimensional drawings | M5000 Series User Manual...
Need help?
Do you have a question about the M5000 Series and is the answer not in the manual?
Questions and answers