Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for 4IPNET EAP200
Summary of Contents for 4IPNET EAP200
- Page 1 EAP200 V1.00 Enterprise Access Point 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
-
Page 2: Copyright Notice
4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content. All other brand and product names are claimed or registered marks of their respective companies or organizations. -
Page 3: Fcc Caution
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Copyright © 4IPNET, INC. All rights reserved. 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299... - Page 4 This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.
-
Page 5: Package Contents
EAP200 Enterprise Access Point ENGLISH Preface Package Contents 4ipnet EAP200 is a high-end 802.11n/b/g 2.4GHz 1. 4ipnet EAP200 x 1 MIMO Access Point (AP) with the best price/ 2. Quick Installation Guide (QIG) x 1 performance for business and industrial applications 3. -
Page 6: System Overview
Antenna Panel Figure 3 EAP200 Antenna Panel Antenna Connector: Attach the antennas here. The system supports one RF interface with two SMA connectors. Copyright © 4IPNET, INC. All rights reserved. 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299... - Page 7 LED ON constantly for 5 seconds LED ON constantly for 5 seconds WES Fail LED OFF LED OFF USB LED Disabled for future usage only. Copyright © 4IPNET, INC. All rights reserved. 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
-
Page 8: Hardware Installation
2. Connect EAP200 to your network device. Connect one end of the Ethernet cable to the LAN port of EAP200 and the other end of the cable to a switch, a router or a hub. EAP200 is then connected to your existing wired LAN network. -
Page 9: Getting Started
1. To access the web management interface, connect the administrator PC to the LAN port of EAP200 via an Ethernet cable. Then, set a static IP address on the same subnet mask as EAP200 in TCP/IP of your PC, such as the following example: IP Address: 192.168.1.100... - Page 10 EAP200 Enterprise Access Point ENGLISH Figure 6 Administrator Login Page 4. After a successful login into EAP200, a System Overview page of web management interface will appear, as depicted below. Figure 7 The Web Management Interface - System Overview Page 5.
-
Page 11: Common Settings
Enter the old password and then a new password with a length of up to 32 characters, and retype it in the Re-enter New Password field. Click SAVE to save the changes. Copyright © 4IPNET, INC. All rights reserved. 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299... - Page 12 Select your preferred Band and Channel for you wireless connection. For example, select 802.11b+802.11g for the band and 6 for the channel. Copyright © 4IPNET, INC. All rights reserved. 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
- Page 13 Step 3. Configure VAP (Virtual Access Point) Profile Settings Figure 11 VAP Configuration Page (VAP-1 shown) EAP200 supports up to 8 virtual APs (VAPs). Configure VAP profile settings (a) Select the VAP Configuration tab to configure the settings of the desired VAP.
- Page 14 EAP200 Enterprise Access Point ENGLISH Figure 12 Virtual AP Overview Page If you use another EAP200 as the peer AP, simply repeat the above-mentioned steps to configure another peer AP(s). On each and every configuration page, you may Click SAVE to save the changes, but you must reboot the system upon the completion of all Note: configuration settings for the changes to take effect.