4IPNET EAP210 Quick Installation Manual
  1. Manuals
  2. Brands
  3. 4IPNET Manuals
  4. Wireless Access Point
  5. EAP210
  6. Quick installation manual

4IPNET EAP210 Quick Installation Manual

Enterprise
Hide thumbs Also See for EAP210:
Table of Contents

Advertisement

Quick Links

Download this manual
EAP210 V1.00
Enterprise Access Point

Advertisement

Table of Contents
loading

Related Manuals for 4IPNET EAP210

Summary of Contents for 4IPNET EAP210

  • Page 1 EAP210 V1.00 Enterprise Access Point...

  • Page 2: Copyright Notice

    4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content. All other brand and product names are claimed or registered marks of their respective companies or organizations.
  • Page 3 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Copyright © 4IPNET, INC. All rights reserved.
  • Page 4 This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.
  • Page 5 EAP210 Enterprise Access Point ENGLISH Preface Package Contents 4ipnet EAP210 is a high-end 802.11a/b/g/n 2.4GHz/ 1. 4ipnet EAP210 x 1 5GHz MIMO Selectable Dual Band Access Point 2. Quick Installation Guide (QIG) x 1 (AP) designed to maximize deployment flexibility 3.

  • Page 6: System Overview

    Quick Installation Guide EAP210 Enterprise Access Point ENGLISH System Overview Front Panel Figure 1 EAP210 Front Panel Rear Panel 1 (1) 1 (2) Figure 2 EAP210 Rear Panel Copyright © 4IPNET, INC. All rights reserved.
  • Page 7 LED (Green) OFF LED (Green) OFF 7 Console Port To access EAP210 via the console interface Right-Side Panel On the right side of the panel there is a Kensington slot. Admin can also fill it with a rubber plug. Copyright © 4IPNET, INC. All rights reserved.

  • Page 8: Hardware Installation

    2. Connect EAP210 to your network device. Connect one end of the Ethernet cable to the Uplink port of EAP210 and the other end of the cable to a switch, a router or a hub. EAP210 is then connected to your existing wired LAN network.

  • Page 9: Getting Started

    1. To access the Web Management Interface, connect the administrator PC to the LAN port of EAP210 via an Ethernet cable. Then, set a static IP address on the same subnet mask as EAP210 in TCP/IP of your PC, such as the following example: IP Address: 192.168.1.100...
  • Page 10 EAP210 Enterprise Access Point ENGLISH 4. After a successful login to EAP210, a System Overview page of the Web Management Interface will appear, as depicted below. The Radio Status and AP Status will be shown. The Web Management Interface - System Overview Page 5.

  • Page 11: Common Settings

     Enter the old password and then a new password with a length of up to 32 characters, and retype it in the Re-enter New Password field.  Click SAVE to save the changes. Copyright © 4IPNET, INC. All rights reserved.
  • Page 12  Select the RF card you would like to set up.  Determine the Band and Channel settings: Select your preferred Band and Channel for you wireless connection. For example, select 802.11g+802.11n for the band and 6 for the channel. Copyright © 4IPNET, INC. All rights reserved.
  • Page 13 Step 3. Configure VAP (Virtual Access Point) Profile Settings VAP Configuration Page (RF Card A : VAP-1 shown)  The EAP210 supports up to 16 virtual APs (VAPs).  Configure VAP profile settings： (a) Select the VAP Configuration tab to configure the settings of the desired VAP.
  • Page 14 Step 4. Configure WDS (Wireless Distribution System) Settings (Optional) To extend the wireless coverage, EAP210 supports up to 4 WDS links per RF card for connecting wirelessly to other WDS-capable APs, or peer APs. By default, all WDS profiles are disabled.
  • Page 15 (a) Enable WDS. (b) Enter the MAC Address (peer AP) and then Click SAVE. If you are using another EAP210 as the peer AP, simply repeat the above-mentioned steps to configure another peer AP(s). On each and every configuration page, you may click SAVE to save the changes of your configured settings, but you must reboot the system for the changes to take effect.

Table of Contents