4IPNET EAP705 Product Handbook
  1. Manuals
  2. Brands
  3. 4IPNET Manuals
  4. Wireless Access Point
  5. EAP705
  6. Product handbook

4IPNET EAP705 Product Handbook

Enterprise access point
Hide thumbs Also See for EAP705:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Product Handbook
EAP705 V1.00
Enterprise Access Point

Advertisement

Table of Contents
loading

Related Manuals for 4IPNET EAP705

Summary of Contents for 4IPNET EAP705

  • Page 1 Product Handbook EAP705 V1.00 Enterprise Access Point...

  • Page 2: Copyright Notice

    4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content. All other brand and product names are claimed or registered marks of their respective companies or organizations.

  • Page 3: Fcc Caution

    Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Copyright © 4IPNET, INC. All rights reserved.
  • Page 4 This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.

  • Page 5: Package Contents

    EAP705 Enterprise Access Point ENGLISH Preface Package Contents The 4ipnet EAP705 Wall Jack Access Point is an 1. 4ipnet EAP705 x 1 on-the-wall as well as a ceiling-mounted dual radio 2. Quick Installation Guide (QIG) x 1 Wi-Fi IEEE 802.11b/g/n + a/n/ac 2 X 2 MIMO 3.

  • Page 6: System Overview

    1 LAN 1 – 2 Ports Attach Ethernet cables here to connect to the wired local network. RJ45 Passthrough for phone or IP devices 2 Bypass 3 DC Jack 12V Attach the power adaptor here. Copyright © 4IPNET, INC. All rights reserved.
  • Page 7 PoE is supported. For Uplink connection. This port can be used to connect to a controller, 3 Uplink (PoE) Port gateway, or directly to the internet. PoE is supported. Copyright © 4IPNET, INC. All rights reserved.

  • Page 8: Hardware Installation

    Please follow the steps mentioned below to install the hardware of EAP705: Step 1. Place the EAP705 at the best location. The best location is usually at the center of your intended wireless network. The EAP705 can be mounted on wall outlets or on any flat surface;...
  • Page 9 To lock/unlock Access Point from the mounting plate, use the Lock Tool provided. Now, the Hardware Installation is complete. • Punch down tools may vary by country. Please contact the 4ipnet Support Team for recommendations if needed. • Please use only the power adapter supplied with the package. Using a different power adapter may damage this system.

  • Page 10: Getting Started

    1. To access the Web Management Interface, connect the administrator PC to the LAN port of EAP705 via an Ethernet cable. Then, set a static IP address on the same subnet mask as EAP705 in TCP/IP of your PC, such as the following example: IP Address: 192.168.1.100...
  • Page 11 EAP705 Enterprise Access Point ENGLISH 4. After a successful login to EAP705, a System Overview page of the Web Management Interface will appear, as depicted below. The Radio Status and AP Status will be shown. The Web Management Interface - System Overview Page 5.

  • Page 12: Common Settings

    Click on the Utilities icon on the main menu, and select the Change Password tab. Enter the old password and then a new password with a length of up to 32 characters, and retype it in the Re-enter New Password field. Click SAVE to save the changes. Copyright © 4IPNET, INC. All rights reserved.
  • Page 13 Select the RF card you would like to set up. Determine the Band and Channel settings: Select your preferred Band and Channel for you wireless connection. For example, select 802.11g+802.11n for the band and 6 for the channel. Copyright © 4IPNET, INC. All rights reserved.
  • Page 14 ENGLISH Step 3. Configure VAP (Virtual Access Point) Profile Settings VAP Configuration Page (VAP-1 shown) The EAP705 supports up to 8 virtual APs (VAPs) per radio. Configure VAP profile settings ： (a) Select the VAP Configuration tab to configure the settings of the desired VAP.
  • Page 15 Virtual AP Overview Page Step 4. Configure WDS (Wireless Distribution System) Settings (Optional) To extend the wireless coverage, EAP705 supports up to 4 WDS links for connecting wirelessly to other WDS-capable APs, or peer APs. By default, all WDS profiles are disabled.
  • Page 16 (a) Enable WDS. (b) Enter the MAC Address (peer AP) and then Click SAVE. If you are using another EAP705 as the peer AP, simply repeat the above-mentioned steps to configure another peer AP(s). On each and every configuration page, you may click SAVE to save the changes of your configured settings, but you must reboot the system for the changes to take effect.

Table of Contents