Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for 4IPNET EAP110
Summary of Contents for 4IPNET EAP110
- Page 1 EAP110 V1.10 Enterprise Access Point...
-
Page 2: Copyright Notice
4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content. All other brand and product names are claimed or registered marks of their respective companies or organizations. -
Page 3: Fcc Caution
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Copyright © 4IPNET, INC. All rights reserved. - Page 4 This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by 4IPNET, Inc. The use of software or firmware not provided and supported by 4IPNET, Inc. may result in the equipment no longer being compliant with the regulatory requirements.
- Page 5 EAP110 Enterprise Access Point ENGLISH Preface Package Contents 4ipnet EAP110 is a high-end 802.11n/b/g 2.4GHz 1. 4ipnet EAP110 x 1 MIMO Access Point (AP) with the best price/ 2. Quick Installation Guide (QIG) x 1 performance for wireless connectivity in enterprise 3.
-
Page 6: System Overview
Press and hold the button for more than 10 seconds until WLAN LED OFF. WLAN ON Reset while reset is successful. Antenna Attach the antennas here. The system supports one RF interface with two SMA Connector connectors. Copyright © 4IPNET, INC. All rights reserved. - Page 7 WLAN LED BLINKING QUICKLY WES Success WLAN LED ON constantly for 5 seconds WES Fail WLAN LED OFF for 5 seconds 3 Power LED LED ON indicates power on; OFF indicates power off. Copyright © 4IPNET, INC. All rights reserved.
-
Page 8: Hardware Installation
2. Connect EAP110 to your network device. Connect one end of the Ethernet cable to the LAN port of EAP110 and the other end of the cable to a switch, a router or a hub. EAP110 is then connected to your existing wired LAN network. -
Page 9: Getting Started
1. To access the web management interface, connect the administrator PC to the LAN port of EAP110 via an Ethernet cable. Then, set a static IP address on the same subnet mask as EAP110 in TCP/IP of your PC, such as the following example: IP Address: 192.168.1.100... - Page 10 Quick Installation Guide EAP110 Enterprise Access Point ENGLISH 4. After a successful login into EAP110, a System Overview page of web management interface will appear, as depicted below. The Web Management Interface - System Overview Page 5. To logout, simply click on the Logout button at the upper right hand corner of the interface to return to the Administrator Login Page.
-
Page 11: Common Settings
Click on the Utilities main menu button, and then select the Change Password tab. Enter the old password and then a new password with a length of up to 32 characters, and retype it in the Re-enter New Password field. Click SAVE to save the changes. Copyright © 4IPNET, INC. All rights reserved. - Page 12 Click on the Wireless main menu button, and then select the General tab. Determine the Band and Channel settings: Select your preferred Band and Channel for you wireless connection. For example, select 802.11g+802.11n for the band and 1 for the channel. Copyright © 4IPNET, INC. All rights reserved.
- Page 13 Step 3. Configure VAP (Virtual Access Point) Profile Settings VAP Configuration Page (VAP-1 shown) EAP110 supports up to 8 virtual APs (VAPs). Configure VAP profile settings： (a) Select the VAP Configuration tab to configure the settings of the desired VAP.
- Page 14 ENGLISH Step 4. Configure WDS (Wireless Distribution System) Settings (Optional) To extend the wireless coverage, EAP110 supports up to 4 WDS links for connecting wirelessly to other WDS-capable APs (peer APs). By default, all WDS profiles are disabled. Click on the Wireless main menu button.