4IPNET EAP717 Quick Installation Manual
  1. Manuals
  2. Brands
  3. 4IPNET Manuals
  4. Wireless Access Point
  5. EAP717
  6. Quick installation manual

4IPNET EAP717 Quick Installation Manual

Enterprise access point
Hide thumbs Also See for EAP717:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
EAP717 V1.00
Enterprise Access Point

Advertisement

Table of Contents
loading

Related Manuals for 4IPNET EAP717

Summary of Contents for 4IPNET EAP717

  • Page 1 EAP717 V1.00 Enterprise Access Point...

  • Page 2: Copyright Notice

    4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content. All other brand and product names are claimed or registered marks of their respective companies or organizations.

  • Page 3: Fcc Caution

    This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. If this device is going to be operated in 5.15 ~ 5.25GHz frequency range, then it is restricted in indoor environment only. Copyright © 4IPNET, INC. All rights reserved.
  • Page 4 This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.

  • Page 5: Package Contents

    EAP717 Enterprise Access Point ENGLISH Preface Package Contents The 4ipnet EAP717 Enterprise Access Point is an 1. 4ipnet EAP717 x 1 on-the-wall as well as a ceiling-mounted Wi-Fi IEEE 2. Quick Installation Guide (QIG) x 1 802.11n/a/b/g 2 x 2 MIMO access point, designed to 3.

  • Page 6: System Overview

    4 LED lights. Representation is listed at the top of the panel. 4 Phone Jack A telephone can bypass to a connected phone line in the back of the AP when connected to the socket. Attach the power adaptor here. 5 5V Copyright © 4IPNET, INC. All rights reserved.
  • Page 7 2 Restart / Reset Button Press once to restart the system; Press and hold for more than 5 seconds to reset to factory default. To access EAP717 via the console interface. 3 Console Port Copyright © 4IPNET, INC. All rights reserved.

  • Page 8: Hardware Installation

    Please follow the steps mentioned below to install the hardware of EAP717: Step 1. Place the EAP717 at the best location. The best location is usually at the center of your intended wireless network. If admin would like to mount the AP on the wall (on a socket), please refer to the included EAP717/EAP747/EAP757 Connection Guide.

  • Page 9: Getting Started

    1. To access the Web Management Interface, connect the administrator PC to the LAN port of EAP717 via an Ethernet cable. Then, set a static IP address on the same subnet mask as EAP717 in TCP/IP of your PC, such as the following example: IP Address: 192.168.1.100...
  • Page 10 EAP717 Enterprise Access Point ENGLISH 4. After a successful login to EAP717, a System Overview page of the Web Management Interface will appear, as depicted below. The Radio Status and AP Status will be shown. The Web Management Interface - System Overview Page 5.

  • Page 11: Common Settings

     Enter the old password and then a new password with a length of up to 32 characters, and retype it in the Re-enter New Password field.  Click SAVE to save the changes. Copyright © 4IPNET, INC. All rights reserved.
  • Page 12  Select the RF card you would like to set up.  Determine the Band and Channel settings: Select your preferred Band and Channel for you wireless connection. For example, select 802.11g+802.11n for the band and 6 for the channel. Copyright © 4IPNET, INC. All rights reserved.
  • Page 13 Step 3. Configure VAP (Virtual Access Point) Profile Settings VAP Configuration Page (VAP-1 shown)  The EAP717 supports up to 8 virtual APs (VAPs).  Configure VAP profile settings： (a) Select the VAP Configuration tab to configure the settings of the desired VAP.
  • Page 14 Virtual AP Overview Page Step 4. Configure WDS (Wireless Distribution System) Settings (Optional) To extend the wireless coverage, EAP717 supports up to 4 WDS links for connecting wirelessly to other WDS-capable APs, or peer APs. By default, all WDS profiles are disabled.
  • Page 15 (a) Enable WDS. (b) Enter the MAC Address (peer AP) and then Click SAVE. If you are using another EAP717 as the peer AP, simply repeat the above-mentioned steps to configure another peer AP(s). On each and every configuration page, you may click SAVE to save the changes of your configured settings, but you must reboot the system for the changes to take effect.

Table of Contents