Rear Panel ......................8 Channel Controls.....................8 Digital Effect Processor..................9 Master Section ....................10 APPLICATION.....................13 DIGITAL EFFECT TABLE..................15 SPECIFICATIONS....................16 DIMENSIONS......................18 BLOCK DIAGRAMS....................19 Phonic reserves the right to improve or alter any information suppied within this document without prior notice. V1.0 APR 14, 2006...
Features Common Features: Thank you for choosing one of Phonic’s many quality compact mixers. The brand new AM 442D and AM Audiophile-quality & ultra low noise 642D Mixers – designed by the ingenious engineers 4 stereo channels with 4-band EQ that have created a variety of mixers fantastic in style and performance in the past –...
Getting Started Channel Setup 1. Ensure all power is turned off on your mixer. To 1. To ensure the correct audio level of the totally ensure this, the AC cable should not be input channel is selected, each of the Mixer’s connected to the unit.
Making Connections 3. Stereo Channels The AM 442D and AM 642D also feature a few Inputs and Outputs Each of these stereo channels features two 1/4” 1. XLR Microphone Jacks These jacks accept typical 3pin XLR inputs for balanced and external signal processors or mixers. If you wish and unbalanced signals.
Rear Panel 11. Channel Inserts etcetera). through to 4 on the AM 442D and 1 through 6 on the AM 642D. This send and return will require a Y cord that can send (pre-fader and pre-EQ) and receive signals to and from an external processor.
Controls and Settings stage rumble. This Low Cut Filter is only available on Mic channels on both the AM 442D and AM 642D. Rear Panel 16. Phantom Power Switch 19. Line/Mic Gain Control...
This control alters the signal level that is sent to the 31. Digital Effect Display EFX send (AUX 2 on the AM 442D, AUX 3 on the AM This 2-digital numeric display shows the program 642D) output and the built-in digital effect processor.
AUX is plugged into the AUX Return 2 inputs, this control Send 2 (on the AM 442D) or the AUX Send 3 (on the AM 642D) outputs, as well as the built-in digital Effect Engine.
Page 11
43. 2T Return Controls Turning the 2T Return level control adjusts the signal level of the feed from the 2T Return inputs, the signal of which is sent to the Main L/R mixing bus. Pushing the “to Ctrl Rm” button (featured on the AM642D only) sends the signal to the Control Room/Phones mixing bus also.
Page 12
49. Graphic Equalizer (AM 642D) This stereo 9 band graphic equalizer allows the user to adjust the frequency response of a signal, with a maximum of ±12 dB of signal boost or cut for each of the frequencies. The AUX 1 / MAIN switch alternates the use of the equalizer between the use of the AUX 1 bus and MAIN L/R bus signals.
DIGITAL EFFECT TABLE PROGRAM NAME PARAMETER SETTING PROGRAM NAME PARAMETER SETTING ROOM REV-TIME EARLY LEVEL SPEED TYPE COMPACT ROOM 1 0.05 SLOW PAN R-->L COMPACT ROOM 2 SLOW PAN 1 R<-->L SMALL ROOM 1 0.45 SLOW PAN 2 R-->L SMALL ROOM 2 MID SHIFT R<-->L MID ROOM 1...
SPECIFICATIONS AM442D AM642D Inputs Total Channels Balanced Mono Mic / Line channel Balanced Stereo Line Channel Aux Return 2 stereo 2 stereo 2T Input Stereo RCA Stereo RCA Outputs Main L/R Stereo 2 x 1/4” TRS, Bal. & 2 x XLR 2 x 1/4”...
Page 17
Crosstalk (1KHz @ 0dBu, 20Hz to 20KHz bandwidth, channel in to main L/R outputs) Channel fader down, other channels <-90 dB <-90 dB at unity Noise (20Hz~20KHz; measured at main output, Channels 1-4 unit gain; channels 1/3 as far left as possible, channels 2/4 as far right as pos- sible.
BLOCK DIAGRAMS AM442D BLOCK DIAGRAMS EFX IN LOGIC POST R POST L PRE R PRE L AUX2 EFX AUX1 MAIN R MAIN L AM442D/642D...
Page 20
AM642D BLOCK DIAGRAMS EFX IN LOGIC POST R POST L PRE R PRE L AUX3 EFX AUX2 AUX1 MAIN R MAIN L AM442D/642D...
Page 21
Phonic, at its option, shall repair or replace the defective unit covered by this warranty. Please retain the dated sales receipt as evidence of the date of purchase.