Zephyr Tornado II AK8200AS Use, Care And Installation Manual
Hide thumbs
Also See for Tornado II AK8200AS:
- Use, care and installation manual (23 pages) ,
- Use, care and installation manual (22 pages)
Related Manuals for Zephyr Tornado II AK8200AS
Summary of Contents for Zephyr Tornado II AK8200AS
- Page 1 Tornado II AK8200AS Tornado III AK8300ASX Model number: Serial Number: Date of Purchase: Sales Dealer: JAN08.0301 © 2008 Zephyr Corporation READ AND SAVE THESE INSTRUCTIONS...
- Page 2 www.zephyronline.com...
- Page 3 SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options ............Specifi cations ............... Electrical ................. Installing the Power Pack ........Single and Dual Internal Blowers ......External Blower Preparation ........FEATURES &...
- Page 4 www.zephyronline.com READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
-
Page 5: Operation
OPERATION Always leave safety grilles and fi lters in place. Without these components, operating blowers could catch onto hair, fi ngers and loose clothing. The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product. -
Page 6: Hardware Package Contents
www.zephyronline.com MODELS: AK8200AS AND AK8300ASX PARTS SUPPLIED AK8200AS AK8300ASX 1 - Power Pack 1 - Power Pack 2 - Decorative mesh fi lters 3 - Decorative mesh fi lters 2 - Halogen light bulbs (pre-installed) 4 - Halogen light bulbs (pre-installed) 1 - Dual internal blower (pre-installed) 1 - 8”... - Page 7 Equivalent number Equivalent number Duct pieces Duct pieces length x used T otal length x used T otal 3-1/ 4” x 10” 1 Ft. 6” Round 30 Ft. Rect., wall cap straight with damper 6” Round, 1 Ft. 6” Round, 30 Ft.
- Page 8 www.zephyronline.com Minimum mount height between range top to hood bottom should be no less than 26”. Maximum mount height should be no higher than 36”. It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fi...
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certifi ed Silver Tape or Duct Tape. Some Ducting Options side wall cap side wall cap...
- Page 10 www.zephyronline.com ” ” ” ” elec. ” 15/16 ” ” 13/16 AK8200AS AK8200AS front ” 7/16 ” ” 11/16 ” 13/16 AK8200AS/AK8300ASX side ” ” ” ” A: elec. B: ext. ” blower ” 7/16 AK8300ASX AK8300ASX front *note: 8” round transition is only needed if using power pack with a dual internal or external blower.
- Page 11 ELECTRICAL WARNING All Electrical work must be performed by qualifi ed electrician or person with similar technical know how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances.
- Page 12 www.zephyronline.com CAUTION: At least two installers are AK8200AS AK8300ASX required due to the weight and size of the ” 1/16” 11/16 hood. 1. Install blower into Power Pack AK8200AS - Blower is pre-installed AK8300ASX - Refer to page 11 for instructions Remove support screw from top of Power Pack before installing into cabinet.
- Page 13 MULTIPLE BLOWERS ARE COMPATIBLE WITH AK8300ASX ONLY. AK8200AS INCLUDES A 1000 CFM DUAL BLOWER ONLY. FOR EXTERNAL BLOWER INSTRUCTIONS TURN TO PAGE 12. 1. Position blower plate over bracket on inside 2. Connect 6 pin male connector from blower back of hood and pivot up. Secure plate to hood wiring to 6 pin female connector in the power with (2) 10x3/16”...
- Page 14 www.zephyronline.com 2. Install threaded end of external blower wiring 1. Place 8” round adapter on top of power pack through external blower wiring knock out (B) and secure with (4) M4x8 screws. Connect 8” located in junction box on top of power pack. round duct work to 8”...
- Page 15 Lights On/Dim/Off Display (Speed level, Delay Off Indicator) 5 Min Delay Off Blower On/Off Adjust 3 Speed Levels Blower On/Off By pressing , the blower is switched On and Off. When switched on, the blower turns on at the same speed it was switched off at.
-
Page 16: Remote Control Features
The RF remote control is equipped with a magnet for easy storage. The remote may be placed on any magnetic surface such as a refrigerator or the Zephyr remote holder. Maximum remote control communication distance from power pack is 15 feet. -
Page 17: Surface Maintenance
SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/ scoring pads which will scratch and damage surface. Do not use products containing chlorine bleach or orange cleaners. For heavier soil use liquid degreaser. -
Page 18: Replacing Light Bulbs
Replacement bulbs are available at specialty lighting stores. Purchase type MR16 (GU-10) 35W halogen. For Zephyr part numbers please turn to page 18 of the manual. Bottom View... - Page 19 TROUBLESHOOTING PROCEDURES FOR TORNADO II AND TORNADO III Issue Cause What to do After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2.
- Page 20 www.zephyronline.com DESCRIPTION PART # Replacement Parts Light Bulb MR16 (GU10) 35W (each) Z0B-0023 Decorative Mesh Filter (each) 50200023 Optional Accessories Single blower (AK8300ASX only) CBI-600B Dual blower (AK8300ASX only) PBI-1100A External blower (AK8300ASX only) CBE-1000 *Baffl e Filter Kit (AK8200AS) Z0F-B082 *Baffl...
- Page 21 Product damaged through negligence, misuse, abuse, accident. Improper installation and failure to follow installation instructions. When product is used commercially or other than its intended purpose. Damaged because of improper connection with equipment of other manufacturers. Repaired or modifi ed by anyone other than Zephyr’s Authorized Agents. What is Not Covered: Consumable parts such as light bulbs, fi...
Need help?
Do you have a question about the Tornado II AK8200AS and is the answer not in the manual?
Questions and answers